Page 1 of 2 12 LastLast
Results 1 to 15 of 19
  1. #1
    Join Date
    Oct 2011
    Location
    adelaide
    Posts
    4

    Default easiest way to cut 5" disc out of mdf

    hi every one i was hoping on a couple of hints on cutting some 5" disc out of mdf i need a hole in the middle as well about 1" all hints would be greatly recived
    thanks craig

  2. #2
    Join Date
    Nov 2004
    Location
    Millmerran,QLD
    Age
    74
    Posts
    1,761

    Default

    Craig

    A lot depends on how many discs you need to make and if you have a router. It may be easiest to make up a template and use a flush trimming bit with a top bearing. This is very easy if you are able to fix the template to your mdf with a couple of small screws.

    Regards
    Paul
    Bushmiller;

    "Power tends to corrupt. Absolute power corrupts, absolutely!"

  3. #3
    Join Date
    Oct 2011
    Location
    adelaide
    Posts
    4

    Default

    thanks paul i have a lot to cut proably about 40 out of 12mm mdf i will make a template and start cutting
    thanks craig

  4. #4
    Join Date
    Nov 2004
    Location
    Millmerran,QLD
    Age
    74
    Posts
    1,761

    Default

    [QUOTE=camele;1581823]thanks paul i have a lot to cut proably about 40 out of 12mm mdf i will make a template and start cutting
    thanks craig[/QUOTE

    Craig

    Template is the way to go for that quantity. You can put a pilot hole in the centre of the template too and drill that at the same time you use the router. Then the hole in your disc can be enlarged with the correct sized spade or forstner bit.

    Also the exact way you go about this depends on the level of accuracy you require for the project.

    Regards
    Paul
    Bushmiller;

    "Power tends to corrupt. Absolute power corrupts, absolutely!"

  5. #5
    crowie's Avatar
    crowie is offline Life's Good, Enjoy each new day & try to encourage
    Join Date
    Dec 2009
    Location
    Faulconbridge, Lower Blue Mountains
    Age
    68
    Posts
    2,576

    Default

    You could also use bi-metal holesaws or T/C holesaws for 40 of them???

  6. #6
    Join Date
    Nov 2004
    Location
    Millmerran,QLD
    Age
    74
    Posts
    1,761

    Default

    Quote Originally Posted by crowie View Post
    You could also use bi-metal holesaws or T/C holesaws for 40 of them???
    Crowie

    Good idea, which I hadn't thought of. 125mm is pretty big so I think you would need a drill capable of quite a slow speed.

    Regards
    Paul
    Bushmiller;

    "Power tends to corrupt. Absolute power corrupts, absolutely!"

  7. #7
    Join Date
    Oct 2011
    Location
    adelaide
    Posts
    4

    Default

    unfortanatly i dont have a drill press but if i did that would b the go. i think the best way will b the router
    thank for the tips guys craig

  8. #8
    Join Date
    Mar 2004
    Location
    Central Coast
    Age
    77
    Posts
    43

    Default

    Quote Originally Posted by camele View Post
    hi every one i was hoping on a couple of hints on cutting some 5" disc out of mdf i need a hole in the middle as well about 1" all hints would be greatly recived
    thanks craig
    Hi Camele
    I would like to offer some help to you on the cutting of 5” disc I am not sure what tools you have available to you but here is a method of cutting a disks with a band a saw if you do not have a band saw go to your nearest men’s shed they would have one and may even do the job for you here is a video of the procedure Cutting discs on a bandsaw, using a simple jig - YouTube
    There are other jigs that you could use you can see them all on You Tube.
    If you need more help or information just PM and I will assist you. there are other simple jigs you could make as well.

    Colbra
    May your saw stay sharp and your nails never bend

  9. #9
    Join Date
    Aug 2010
    Location
    ACT
    Age
    85
    Posts
    546

    Default

    You could use a trammel on your router and the pivot hole in the centre would be the centre for a forstner bit or spade bit.
    The guide plate that comes as standard with a Triton router would be ideal.
    Regards
    Last edited by A Duke; 3rd December 2012 at 10:28 AM. Reason: Spell checker could not spell forstner either
    Hugh

    Enough is enough, more than enough is too much.

  10. #10
    Join Date
    Nov 2004
    Location
    Millmerran,QLD
    Age
    74
    Posts
    1,761

    Default

    Quote Originally Posted by A Duke View Post
    You could use a trammel on your router and the pivot hole in the centre would be the centre for a fosner bit or spade bit.
    The guide plate that comes as standard with a Triton router would be ideal.
    Regards
    Hugh

    I have found that is the easiest option for larger circles, but I didn't mention it in this case because because the radius of the hole will be relatively small and a bit fiddly to set up unless the router is small. A laminate trimmer might suit but their fence system does not usually have provision to insert a single rod.

    Regards
    Paul
    Last edited by Bushmiller; 3rd December 2012 at 09:32 AM. Reason: doubled up on words
    Bushmiller;

    "Power tends to corrupt. Absolute power corrupts, absolutely!"

  11. #11
    Join Date
    Aug 2010
    Location
    ACT
    Age
    85
    Posts
    546

    Default

    Quote Originally Posted by Bushmiller View Post
    Hugh

    I have found that is the easiest option for larger circles, but I didn't mention it in this case because because the radius of the hole will be relatively small and a bit fiddly to set up unless the router is small. A laminate trimmer might suit but their fence system does not usually have provision to insert a single rod.

    Regards
    Paul
    Paul,
    You are probably right, two and a half inches radius is rather small.
    Trying to solve some one else's problems is difficult as you have less than half the info, only what they want to do and not the available equipment and skill level.
    It could be as simple as telling a computer to tell the CNC what to do.
    Regards
    Hugh

    Enough is enough, more than enough is too much.

  12. #12
    Join Date
    Dec 2010
    Location
    Melbourne
    Age
    80
    Posts
    36

    Default

    I have never had much luck useing a hole saw,the disc get stuck in the saw,IMO the router path is the neatest way to go

  13. #13
    Join Date
    Oct 2006
    Location
    Tallahassee FL USA
    Age
    82
    Posts
    0

    Default

    Five inch is probably too small for this: https://www.woodworkforums.com/f88/router-compass-50372/

    but you could use an auxiliary base plate with a pivot at 2.5" radius (a simple nail projecting downward). The nail hole in the stock can provide a target for the Forstner bit.

    Cheers,
    Joe
    Of course truth is stranger than fiction.
    Fiction has to make sense. - Mark Twain

  14. #14
    Join Date
    Oct 2011
    Location
    Mount Colah
    Posts
    1

    Default easiest way to cut 5" disc out of mdf

    What you need to achieve is a,say 150mm dia template to use with a guide bush, that will do the 5" dia piece.

    But before you cut that, if you have a drop in piece with a smaller hole (like a donut shape) you can do the inner hole first, remove the piece and do the outer.

    Hole saws and router + trammel will let you make the pieces.

    Care needs to be taken routing the big piece as it becomes detached, so either don't rout full depth, stick the piece down before routing, or have a drop in plug that goes in the small hole and fixes the piece in the jig.

  15. #15
    Join Date
    Oct 2011
    Location
    adelaide
    Posts
    4

    Default

    thanks for the segestions i will also contact the local men's shed in the area as i would like to do this with limiting the dust. i am at present saving for a dusty and a couple of other things but at the moment funds all go to the house and projects for the kids. i don't have a lot of experience working with wood. but i like to learn that what it is all about. again thanks for the help Craig

Similar Threads

  1. easiest way to resize images
    By Auzzie turner in forum NOTHING AT ALL TO DO WITH RENOVATION
    Replies: 19
    Last Post: 24th August 2006, 10:59 PM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •