Results 1 to 9 of 9
Thread: house renos
-
14th October 2023, 01:19 PM #1
house renos
For the first half of the year I had a break from other people's work to renovate our house. Mostly the inside is complete and still to paint the outside. Firstly it involved a lot of time sitting and thinking about room layout and efficient use of space. Then it involved shrinking a non-load bearing wall and lengthening others, a full replacement of all timber trims and floor coverings, a full repaint, change of light fittings and fans, complete change of window coverings. I did everything except the electrical and setting the plaster. First thing was to build a covered pergola to give me an undercover for painting trims and storing materials. The bonus is it reduces the temperature in my workshop considerably.
IMG_5377.jpgIMG_5381.jpg
These are before photos looking from what was our TV/lounge area into the dining room
IMG_5106.jpgIMG_5114.jpg
And the after photo. This room isn't furnished as we'd finally like it, but it is a lovely spot for the winter sun. We have two sets of doors like this and all the windows are similar, I thought it would be a nightmare, but I found the one trick that made painting them to a high standard a breeze - masking paint. We went with the one paint scheme throughout, quarter lexicon on the ceiling and double alabaster for the walls.
IMG_6457.jpgIMG_5509.jpg
These are before photos looking right across our large room, across no-mans-land into the TV area, and facing the other way with the front door being on the other side of my secretaire
69711414175__A65E6B2F-7D3A-4EEE-B6EB-7E6FE2815D7D.jpg69711410986__5BFB9711-F041-491B-AB70-E312930FAFA3.jpg
These are the after photos. We moved the dining room to where the TV area was and no-mans-land becomes the TV area. Eventually I will add a hybrid display storage area on the wall behind the table. We went with DC fans for their efficiency and quietness. Towards the front door I extended the wall to create a more private entry. This area will eventually have a bench seat built in. The wall behind the TV was the one shortened at both ends.
IMG_6463.jpgIMG_6461.jpgIMG_6460.jpg
The house is divided into living areas above and bedrooms off the hall shown below. I knocked out the wall on the right and offset it to create a pocket and added a header to carry zoning doors. I made my Soji doors (still have to install the paper).
IMG_6468.jpgIMG_7752.jpegIMG_7751.jpg
One of the first things I did was a laundry reno, where the tin cabinet under the sinks were replaced with a plywood cabinet for the kitty litter, but was designed to have doors retro fitted. I kept the nice tubs and added the timber bench and overhead storage
IMG_0786.jpgIMG_0787.jpg
I had to use a bit of levelling compound here and there, but one room required four bags of compound to bring it back to flat. This was screeded rather than trowelled for reasons. The floor is a hybrid tile by Karndean.
IMG_6444.jpgIMG_6452.jpg
We went with Veneta honeycomb blinds throughout
IMG_6161.jpg
Thanks for looking
-
27th October 2024, 10:52 AM #2
I'm nearly finished the last of the internal renovations at home with the final major thing being the makeover of our big storage closet that you can see in this photo.
IMG_5504.jpg
First the doors were tossed!
IMG_1442 (1).jpg
Then the closet was gutted but all the shelves were salvaged and cleaned up because they were nice hoop pine. Also the head for the doors was too low making access to the top area difficult, so I moved the beam higher up and made the opening bigger. Drawers are replacing the shelves so I built 3 carcases from melamine. The top shelf is camphor laurel plywood to assist with deterring moths.
IMG_1859 (1).jpg
The top of the drawer unit has a top made from red pine
IMG_1860 (1).jpg
I built 12 drawers from premium birch plywood using lock mitre joinery. Some of the hoop pine shelves went to uprights to transfer the top shelf load.
IMG_1882 (1).jpg
IMG_1886 (1).jpg
The majority of the remaining old hoop pine went to make the drawer fronts
IMG_2350 (1).jpg
-
27th October 2024, 11:21 AM #3
I bought 0.2 cube of Silver Ash from a bloke in Gympie for the doors of the closet
IMG_2790 (1).jpg
This rough timber was converted into a forest of parts for four Shoji doors
IMG_2874 (1).jpg
I also had a few small crotch slabs and boards left from salvaging a neighbours red cedar from the chipper which I used to make transom panels for the doors. These are 8mm thick and consist of between four and six boards per panel
IMG_3165 (1).jpg
I made 4 Kumiko panels out of the smaller dimension silver ash. Actually there are three different widths for these components
IMG_3171 (1).jpg
There are 128 mortises for the four doors for the Kumiko panels alone.
IMG_3172 (1).jpg
I glued up the four doors. This is one of them
IMG_3177 (1).jpg
IMG_3178 (1).jpg
And this is all four now installed into the front of the closet. They run in traditional tracks made of silver ash.
IMG_3181.jpg
The shoji paper is on the way and once that is installed and jambs added and a few internal trims the job will be done
-
27th October 2024, 11:11 PM #4Member
- Join Date
- Jun 2010
- Location
- SW Victoria
- Posts
- 91
Great work there!
-
28th October 2024, 09:11 AM #5
-
29th October 2024, 01:05 AM #6
Really nice work. Well done. Thanks for all the pics. Most impressive.
Are you a registered member? Why not? Click here to register. It's free and only takes around 40 seconds!
Register to get rid of the annoying ads, plus you are able to participate, see all the posts, photos, pdf's, and more.
-
29th October 2024, 08:28 AM #7
-
29th October 2024, 08:06 PM #8GOLD MEMBER
- Join Date
- Oct 2004
- Location
- Melbourne, Australia.
- Posts
- 126
128 mortises for the doors alone, I bet by the time you were finished you were on autopilot!
Mick.
-
30th October 2024, 09:00 AM #9
That's for the kumiko panel only, not for the door frame! I confess in the interests of time management I Dominoed the frame rather than do the double mortise for each joint! Though I did still do the angled shoulder for the Jaguchi joint that gives this look with the chamfer.
IMG_3175.jpg
There is a lot of autopilot in making Shoji! Everything is set out with a story stick to begin with and that's where you have to keep your head, but yeah with the mortises it gets kind of tedious and repetitive.
Similar Threads
-
is everything possible in renos?
By Reno RSS Feed in forum GENERAL ODDS N SODSReplies: 0Last Post: 27th March 2014, 09:20 AM
Bookmarks