![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 106 to 120 of 203
-
6th March 2023, 02:37 PM #106
Senior Member
- Join Date
- Nov 2020
- Location
- Oregon, USA
- Posts
- 143
I'm working on grids for the gable ends. My plan is to make 4 sash that can be applied after the frame is up, backed by screens to keep the bugs out.
My inspiration is this photo from a book:
07B01476-1511-450E-8028-1C9368E00CE4.jpg
And here is my interpretation for my shed.
Gable end grid.jpg
I don't really know the best way to go about this but what I am doing is making a separate sash that can be applied over a sill and inset into the frame.
I made frames for the sash:
7A8091A0-9AC7-4FE8-B700-A03B088AFBB2_1_105_c.jpeg
These are joined simply with saddle joints at the corners that will be glued. But I added a coped joint called in Japanese a jaguchi joint on the outside to accommodate a beveled face. Here is one before clean up.
E3A162C0-6710-4781-9010-07E539025E9D_1_105_c.jpegA23FE649-B38F-42F8-B608-7E68C4154E78_1_105_c.jpeg
The grid will be half lapped and morticed into this frame. That layout on a square frame is not so hard but having a sloped top member introduces some challenges. When i imagined it I said, "No worries, I'll figure that out later. Later is now and I'm still working on the best way forward. Trigonometry is my friend, I hope.
-
6th March 2023, 03:45 PM #107
Well within your capabilities
The person who never made a mistake never made anything
Cheers
Ray
-
25th March 2023, 01:24 PM #108
Senior Member
- Join Date
- Nov 2020
- Location
- Oregon, USA
- Posts
- 143
My first attempt at doing the lattice parts didn't work. I made a jig for the table saw using a dado blade and indexing strip as if I was making box joints. I started on the horizontal parts. The result looked great from afar. Mesmerizing, even.
C2226656-2CF1-4C48-A03C-BCD7B9017BC3.jpg
But for reasons I won't go into the way I did it introduced an incremental increase in slot width from just below the target 22 mm wide to about 22.4 mm wide over 15 cuts on the long horizontal pieces. Not good.
So back to work. I remade the horizontal stock and I'm working on a different approach using a router jig. I had to order a 22 mm bit and it is in hand. The jig is nearly done. I hope to restart tomorrow.
-
31st March 2023, 01:26 PM #109
Senior Member
- Join Date
- Nov 2020
- Location
- Oregon, USA
- Posts
- 143
Plan B seems to be working. An mdf jig/fixture with spacers to add at the proper lattice pitch.
F5ECD25E-B801-4345-97F6-36086E4737AD_1_105_c.jpeg929A0695-35A0-4A29-B7C4-B68C43D196F9_1_105_c.jpegF5ECD25E-B801-4345-97F6-36086E4737AD_1_105_c.jpeg
But my Lord, what a mess of mdf flour and chips everywhere. I did clean up for the pics so you can see what's going on. I really hate using a screaming router but sometimes it is expedient.
-
2nd April 2023, 11:49 AM #110
Senior Member
- Join Date
- Nov 2020
- Location
- Oregon, USA
- Posts
- 143
Horizontal slats are remade. I have half the verticals done, too. The verticals are meant to sit 2 mm proud of the horizontals on the front side and be flush on the back.
There is going to be some challenging joinery where the horizontals and verticals meet the sloping upper rail. I have a plan for it that involves tenoning the verticals but not the horizontals. I hope to get to that part next week.
Pictures are just the parts laid out.
B05C13E8-B5B0-4DDD-864F-8EBFA5ABDD60_1_105_c.jpeg5E8F34DB-D288-4536-8BA3-F6B9FF7A04CE_1_201_a.jpg
-
3rd April 2023, 02:10 PM #111
Senior Member
- Join Date
- Nov 2020
- Location
- Oregon, USA
- Posts
- 143
And the laps on the verticals are done. Here is a quick test fit to see whether everything lines up. The frame is just resting on top. No joinery yet.
B943A3B2-7A71-4BB9-8A63-7CAE268628A6_1_105_c.jpeg
-
4th April 2023, 01:51 PM #112
Senior Member
- Join Date
- Nov 2020
- Location
- Oregon, USA
- Posts
- 143
Here's how, conceptually, I'm planning to do the joinery of the verticals and horizontals along the sloping upper rail. For scale, the horizontals are 18x22 in section and the verticals are 20x22.
F75A09F7-EC67-4735-BD1E-30EC03F0CCA6_1_105_c.jpeg57860C2E-7621-485C-9BEC-0E456FBA05F5_1_105_c.jpegB1BAE3D8-51D8-4755-B6FA-AE5A46EF1E76_1_105_c.jpeg
I have 60 verticals to do and about 24 horizontals. It's going to take me awhile. But this is the fun stuff. Much better than routering.
60F85A91-A31F-480D-9DB3-5153B715984F_1_105_c.jpeg
-
4th April 2023, 06:38 PM #113
That last one at the bottom RHS will test your steady hand and sharp tools
The person who never made a mistake never made anything
Cheers
Ray
-
8th April 2023, 12:33 PM #114
Senior Member
- Join Date
- Nov 2020
- Location
- Oregon, USA
- Posts
- 143
I have the vertical and horizontal lattice slats done. I made a little sawing/planing/paring guide for the verticals and another for the horizontals. They worked great. I could mostly work right off the saw with only a little paring afterward. I decided to carry one of the four frames through to completion as a test case before doing the other three. I hope to catch and not repeat mistakes that way.
I generally like to make mortices first and fit tenons to them but in this case I've done the reverse since the rigid lattice determines the mortice spacing.
E2F29175-15D9-4A9A-9303-1E6E486FC591_1_105_c.jpeg447D5AD3-880B-4A22-B861-BB2B8669B572_1_105_c.jpegA53F315A-4FB8-47B1-A4B1-A295C1CF58FE_1_105_c.jpeg53024ABB-FB73-4253-8EB7-ED5B9FC1CDE3_1_105_c.jpeg
-
13th April 2023, 12:27 PM #115
Senior Member
- Join Date
- Nov 2020
- Location
- Oregon, USA
- Posts
- 143
Fitting this first frame has not gone well but I'm getting closer. Here is a dry fit. Still some tweaking to do to get that upper rail seated properly. I do like the layered look of frame proud of the verticals and beveled, and verticals proud of the horizontals and beveled. In the background you can see the carriage I had to add to my morticer to get the proper mortice angle on the upper rail.
E1AA2082-285D-4D5F-9EF8-958B9DFD6C6C_1_105_c.jpeg
1BB7A48B-F8A4-4E02-B880-B944D974307A_1_105_c.jpeg
-
21st April 2023, 11:46 AM #116
Senior Member
- Join Date
- Nov 2020
- Location
- Oregon, USA
- Posts
- 143
One sash done except for flushing the frame corner joints.
39E718D3-285B-40D3-8684-BCA5CFF782F8_1_105_c.jpegE8FB6E17-89C2-4312-9180-6906433D0EA8_1_201_a.jpg
-
28th April 2023, 12:44 PM #117
Senior Member
- Join Date
- Nov 2020
- Location
- Oregon, USA
- Posts
- 143
A small update. A friend in central New York state, on the other side of the country, sent me a box of cutoffs from wood his son used to build a deck. The wood is commonly called black locust, Robinia pseudoacacia.
Black Locust | The Wood Database (Hardwood)
This is a north American hardwood common to the eastern half of the continent and often used for fence posts because it is extremely rot resistant. It is hard and dense and slightly brittle but machines well. I've never seen it used for furniture but it certainly could be although the tree rarely gets very large. I'm using it for the pegs and wedges and pins for my shed for its rot resistance, because pegs should be harder than the timbers, and because it was free. Well, at least a swap for a birdhouse I made for my friend.
I hope I'm not the only one who gets a surge of pleasure by getting a box of scrap wood in the post.
58F3A26D-CDBA-4FAC-9D75-3B2399D4C80E_1_201_a.jpg
And after a few minutes of band sawing, planing, an chiseling, a couple of wedges. I have 24 more of these to go.
429B867D-735F-4D8E-BEAF-FF5C52670057_1_105_c.jpeg
-
6th May 2023, 11:23 AM #118
Senior Member
- Join Date
- Nov 2020
- Location
- Oregon, USA
- Posts
- 143
I finally finished the four gable end lattices. They aren't perfect but I'm calling them acceptable.
41329ECB-56FA-460C-A122-8C5225F9C5B8_1_201_a.jpg
And here is more or less what a pair will look like with the central post and their sills.
899889CC-3B35-424D-BF79-28101F429731_1_105_c.jpeg
-
9th May 2023, 11:59 AM #119
Senior Member
- Join Date
- Nov 2020
- Location
- Oregon, USA
- Posts
- 143
A weekend project. I'm getting closer to being able to test fit the joinery and I need to have at least one persuader. This one has a head of Oregon white oak (about 2.5 kg) and a European beech handle. I've never made one of these before and wasn't sure how long to make the handle so I left this one maybe a bit long. Better than too short.
I have another one in the works that is about 7 kg. I'm calling that one a commander.
8FB1FE8F-7822-479E-BD85-A7CB281E6E9E_1_105_c.jpegD4194FC2-6312-49DE-B2EC-F754FB71827A_1_105_c.jpeg
-
11th May 2023, 12:28 PM #120
Senior Member
- Join Date
- Nov 2020
- Location
- Oregon, USA
- Posts
- 143
And the second one is done.
17284E49-9F66-4495-AAA4-592455577FB5_1_201_a.jpg
Similar Threads
-
Replacing wood framed windows with aluminium framed
By Reno RSS Feed in forum DOORS, WINDOWS, ARCHITRAVES & SKIRTS ETCReplies: 0Last Post: 14th May 2010, 10:20 PM -
Japanese Dry Stone Garden
By ssgt in forum LANDSCAPING, GARDENING, OUTDOORSReplies: 1Last Post: 21st January 2008, 04:03 PM -
japanese garden
By sinjin1111 in forum LANDSCAPING, GARDENING, OUTDOORSReplies: 3Last Post: 10th March 2006, 06:49 PM