Results 1 to 15 of 15
Thread: WOODWORKING QUIZ for 30 AUG 04
-
30th August 2004, 09:59 PM #1
WOODWORKING QUIZ for 30 AUG 04
Good Evening Friends,
Ever wish you had a frame or platform you could lay sheet goods on while you are cutting pieces with your circular saw and when finished, just put it away?
How would you go about making a KD frame that would work for you?
Respectfully,
P.S. When something is clear as mud, means that it is not clear at all and one could get pretty darned lost in it. As far as the other I won't touch that one with a ten foot pole.Ralph Jones Woodworking
London, Ohio
-
30th August 2004, 10:15 PM #2
I'd do something like this!
Cheers,
P
-
30th August 2004, 10:36 PM #3
I would do something like this.
Or go to here.
http://www.woodworkingtips.com/etips/etip030815sn.htmlLast edited by Barry_White; 30th August 2004 at 10:53 PM.
-
31st August 2004, 07:49 PM #4Registered
- Join Date
- Aug 2003
- Location
- .
- Posts
- 4,816
Hey Midge.
I hope Mum knows you nicked her kitchen table? :eek:
Al
-
31st August 2004, 09:43 PM #5
WOODWORKING QUIZ ANSWER for 30 AUG 04
Good Morning Friends,
Biting midge, you have the exact one that is printed in the Wood Magazine and also the one that the quiz was about.
Congratulations.
Respectfully,Ralph Jones Woodworking
London, Ohio
-
31st August 2004, 09:55 PM #6Originally Posted by Ralph Jones
It's one of the handiest gadgets I own. Of course it's also one of the only projects I've ever completed so there aren't many to choose from!!
Works a treat supporting sheet goods, but also as a cut-off table and a trillion other things, and Oz is right..with a few ply offcuts and a plastic table cloth, no-one can tell!!
Cheers,
P
-
31st August 2004, 10:04 PM #7
G'day.
I think I read that same mag & went out & sketched it on the back
of one of my wife's note pads. :eek:
If you think my drawing is bad, you should see the other side of the
page I drew it on.Cliff.
If you find a post of mine that is missing a pic that you'd like to see, let me know & I'll see if I can find a copy.
-
1st September 2004, 05:26 PM #8
Isn't that what kids are for?
"Last year I said I'd fix the squeak in the cupbaord door hinge... Right now I have nearly finished remodelling the whole damn kitchen!"
[email protected]
-
4th September 2004, 07:29 PM #9Deceased
- Join Date
- Jun 2003
- Location
- ...
- Posts
- 1,460
Midge,
Can you give some more details, sizes and dimensions etc, and other suggestions on this layout table as I am about to build one myself.
Peter.
-
4th September 2004, 08:24 PM #10
yeah Midge me too!
Plausible deniability is the key to success
-
5th September 2004, 08:27 AM #11
It gives me great pleasure!!
Sturdee, MarkV
The details of my table are below, but also check out the Fine WoodWorking Article - A circular saw in the cabinet shop which has an almost identical table in it. After reading that article I built my straight edges and had a life changing experience!!
Overall dimension is 2200 x 930 and weight is 13kg. The light weight is a big advantage in moving it around, and even though the structure is improbably light, the top has about a 6mm sag in it after a LOT of heavy work and abuse. Keeping the length at 2200 means it can be stored on end in room with a normal ceiling height, and will carry a 2400 x 1200 sheet of anything with minimal overhang.
Using it is dead simple, particularly cutting sheet material or docking anything. Set the saw to a few mm thicker than the material and cut through the top. The sacrificial structure will last for years!
The only change I would make if I was to rebuild it (which I won't until it falls apart) is that I would mount the legs on two 90 x45 stringers (laid flat) for the full length of the underside. This would take most of the flex out of it.
My table features legs from Bunnies (about $20 and the only bit that I paid for).
The timber pieces are 45 x 45's cut from warped or damaged pine studs scrounged from building sites. The cross pieces are at 300 centres.
Assembly was dead easy, I used liquid nails in all the joints because it sort of kept stuff together while I screwed in a couple of gyprock screws.
Lay it out upside down on a flat piece of floor and brace it against a wall as you screw. This will ensure that the table top is in one plane as you screw it together.
Hopefully between the article above and the pics attached you'll have enough info...if not get back to me!
Pics show:
1) Sophisticated joinery techniques employed . Note saw cuts typical of the whole top!
2) Top view. I apologise for the contrast in the photo..will try harder in future, but it tells the story.
3) Bottom view of the fixing of the legs. Just a couple of bits of scrap and screws.
Cheers,
P
-
5th September 2004, 09:11 AM #12Supermod
- Join Date
- Jul 1999
- Location
- Brisbane, Qld.
- Age
- 48
- Posts
- 579
hey, whats doing? no smart answers! Poor Ralph will start thinking us Aussies actually do know something!
Cause I travel round the country for work I have to live with just using saw horse's to cut, not only sheet goods, but also sections of shop fittings which happen to have the dimensions of 2400x1200x250. This would certainly make life a little easier (read that as a lot easier ) but can't fit everything on the truck unfortunatly...
-
5th September 2004, 04:15 PM #13Deceased
- Join Date
- Jun 2003
- Location
- ...
- Posts
- 1,460
Thanks for the detailed reply Midge.
I was going to use a couple foldup sawhorses that I have already got for the legs and attach some wheels so that when upright I can easily wheel it away.
When finished I'll post some photos.
Peter.
-
5th September 2004, 06:30 PM #14Originally Posted by Shane Watson
I guess when the moon is low, we actually fluke one??
Cheers,
P
Hey Shane, maybe you could make one that folded into four pieces to travel with? Or even into an airport carry-on bag?
-
5th September 2004, 06:57 PM #15Supermod
- Join Date
- Jul 1999
- Location
- Brisbane, Qld.
- Age
- 48
- Posts
- 579
Originally Posted by bitingmidge
Don't laugh, its been done before...Mind you nowadays, they don't appreciate the likes of drills and hammers etc in your carry on bag.... :eek:
Except one lovely secruity lady asked if I had tools in my luggage and I said yeah of course, who dosn't Der.... and all she was concerned about was wheather the batteries were plugged in or not.
Bookmarks