Results 1 to 9 of 9
Thread: Cracks in veneer
-
29th August 2008, 11:04 AM #1New Member
- Join Date
- May 2007
- Location
- Upwey
- Posts
- 3
Cracks in veneer
Have just purchased a bedside chest with burr-walnut veneer on the drawers. Claimed to be English, 1870s.
There is some slight (fine) cracking of the veneer, but no evidence of any lifting.
Would appreciate advice on how to treat the cracks to prevent further deterioration, or possibly even to close them up, at least visually.
Any suggestions would be most welcome.
-
29th August 2008, 11:09 AM #2
Burr veneered furniture of that vintage usually has plenty of filler in the irregularities already. It could well be that the original beaumontage has fallen out in some places and this is what you're seeing. I would fill any defects with fresh beaumontage.
.
I know you believe you understand what you think I wrote, but I'm not sure you realize that what you just read is not what I meant.
Regards, Woodwould.
-
29th August 2008, 06:38 PM #3New Member
- Join Date
- May 2007
- Location
- Upwey
- Posts
- 3
Thanks Woodwould, will do as you suggest. Do you know of a commercially available beaumontage, or would you start from the basic ingredients?
-
29th August 2008, 06:45 PM #4
If you have the ingredients and the inclination, it's certainly rewarding to make your own beaumontage, but if not, you should be able to purchase some ready made sticks from any good restoration supply shop (and even some of the bad ones too! ).
.
I know you believe you understand what you think I wrote, but I'm not sure you realize that what you just read is not what I meant.
Regards, Woodwould.
-
29th August 2008, 11:26 PM #5New Member
- Join Date
- May 2007
- Location
- Upwey
- Posts
- 3
Thanks again, Woodwould. I won't ask you to name names, so we can protect the guilty!
-
30th August 2008, 01:07 AM #6
Really, I was joking. I'm not aware of any bad restoration supply shops. Not that I know too many anyway. I'll stop digging now.
.
I know you believe you understand what you think I wrote, but I'm not sure you realize that what you just read is not what I meant.
Regards, Woodwould.
-
31st August 2008, 11:34 PM #7
What is beaumontage and how is it used/applied? I got the gist of it but would hate to only know the half of it.
Last edited by prozac; 31st August 2008 at 11:35 PM. Reason: didn't make sense
prozac
____________________________________________
Woodworkforums, cheaper than therapy...........
-
1st September 2008, 08:40 AM #8
Beaumontage is an old-fashioned stopping and I only recommend it as that's most likely what's already in the veneer in places.
Beaumontage consists of equal parts of beeswax and rosin with a small amount of shellac flakes. The whole lot is melted in a tin or small pan and poured into a mould (I had a small wooden mould which I lined with tin foil). The mixture can be coloured to match any wood with the addition of dry pigments.
To apply it, heat a knife, or soldering iron and melt the beaumontage into the cracks or blemishes. Any surplus can be pared off with a sharp chisel..
I know you believe you understand what you think I wrote, but I'm not sure you realize that what you just read is not what I meant.
Regards, Woodwould.
-
1st September 2008, 11:39 AM #9
Thanks Woodwould.
prozac
____________________________________________
Woodworkforums, cheaper than therapy...........
Similar Threads
-
cracks in new brickwork
By contrebasse in forum BRICKWORKReplies: 22Last Post: 26th March 2007, 06:38 PM -
What should I use to fill cracks in ply walls ?
By JDarvall in forum DOORS, WINDOWS, ARCHITRAVES & SKIRTS ETCReplies: 5Last Post: 28th September 2006, 08:57 PM -
French Polish-cracks
By michaelw in forum FINISHINGReplies: 1Last Post: 25th November 2003, 11:20 PM
Bookmarks