Results 1 to 9 of 9
  1. #1
    Join Date
    May 2008
    Location
    melbourne
    Age
    75
    Posts
    0

    Default Belt sander to trim ceramic tile?

    Hi,
    I've taken off the old style high wall mounted toilet cistern; there are 9 tiles to be replaced. I bought some 150 mm plain white tiles and all the other stuff, never down any tiling. When I do a dry run to see how they fit, they don't! The old tiles probably go back to 1957 when the house was originally built. They are slightly smaller than the new 150mm, like 149 mm. They were very tightly set together.

    Is it possible to use my belt sander to take off a mm or two from 3 tiles so they will fit?
    or is the only (cheap) way to get a tile scorer and use pliers to snap of say a 3 mm line? or do I have to get a proper tile cutter, just to cut 3 tiles?

    Thanks

  2. #2
    Join Date
    Dec 2005
    Location
    South Australia
    Posts
    140

    Default

    To make things realy simple contact a supplier of discontinued tiles (yellow pages/Tile shops), they wiil be expensive $4-5 per tile,you could try the sander, I think you wiil go through belts rapily, try one and see how it goes, or take them to your local tile supplier they wiil most likely have a diamond saw and cut them for you.

  3. #3
    Join Date
    Dec 2005
    Location
    Oz
    Posts
    0

    Default

    Doubt a belt sander will do anything. Diamond wheel in an angle grinder is probably the cheapest solution. Or find someone with a tile saw.

  4. #4
    Join Date
    Dec 2007
    Location
    Brisbane
    Posts
    19

    Default

    With most tiles they have different size gradings that are allocated to a batch, for example you could buy 450 sq tiles but they may have for example 6 size grades ranging from 447mm +/- 1mm thru to 453 +/- 1mm. Thats why it's always important to not only get them all from the same batch but also the same size as the difference on larger tiles can be as much as 5 mm between the biggest and smallest grades. I would go to a tile shop and they may just have some that are smaller than 150mm sq.

    I don't think you will get any where with a belt sander and you will end up with a sharp edge which will look funny against the other tiles.

  5. #5
    Join Date
    May 2008
    Location
    melbourne
    Age
    75
    Posts
    0

    Default

    Thanks everyone,

    You've given a lot to go on; I didn't realize there was so much variation in tile sizes! If the original layer had used wider grouting it would've been easier

    Thanks

  6. #6
    Join Date
    Jun 2006
    Location
    Barboursville, Virginia USA
    Age
    77
    Posts
    549

    Default

    Quote Originally Posted by Toolin Around View Post
    Doubt a belt sander will do anything. Diamond wheel in an angle grinder is probably the cheapest solution. Or find someone with a tile saw.
    Toolin' got the right idea. for so few tiles, just catch 'em in a vise and grind 'em down on the edges with a masonry wheel.
    Cheers,

    Bob



  7. #7
    Join Date
    May 2007
    Location
    Cronulla, NSW
    Posts
    58

    Default

    When did we go metric? Some time after 1957 methinks.....

    I have used a beltsander to trim ceramic tiles - just make sure you buy a few cheap, really coarse belts coz it does chew thru em...

  8. #8
    Join Date
    Nov 2007
    Location
    Gunning
    Posts
    33

    Default

    I've done this before. I clamped two pieces of steel with timber strips around the tile leaving the bit for removal exposed and placed the lot in a vice. Then use a masonry wheel in the angle grinder and take the excess off. I found you need to hold the grinder almost horizontal (ie parallel with the steel strips), over the top and along the length of the steel and do it in fast sweeps across the whole tile, removing a bit at a time to keep it flat. Too slow or to much angle and the tile chips or goes wavy. The steel is the guide to stop you going too far. With my tiles I needed the wheel to turn into the dress face of the tile - the other way made the for tiny chips in the glaze. Assuming this technique works on all tiles, one tile for practice and you'll be an expert.

  9. #9
    Join Date
    May 2008
    Location
    melbourne
    Age
    75
    Posts
    0

    Default

    Thanks again,

    good point about metric!: 'cos I thought 5.9 inches is an odd length!. OK so the tiles were done since then. (Now you've got me thinking: what was the 'standard' size in the imperial days? before 1967?)

    Anyway you've told me what I wanted to hear. I've really got the belt disc grinder to sharpen shredder blades, so I might as well use it for something else. But I might ring a tile shop as it sounds so easy if they have slightly smaller tiles..

    Thanks

Similar Threads

  1. Ceramic Tile Underlay for Bathroom
    By Gooner in forum BATHROOM & TOILET
    Replies: 7
    Last Post: 15th April 2008, 03:30 PM
  2. Ceramic tile underlay on bathroom floor
    By JMB in forum BATHROOM & TOILET
    Replies: 2
    Last Post: 16th March 2008, 06:33 PM
  3. Help - Ceramic Tile Underlay
    By Aussiephil in forum TILING
    Replies: 3
    Last Post: 25th April 2007, 01:44 PM
  4. ceramic tile quality
    By stevenroyals in forum TILING
    Replies: 2
    Last Post: 1st June 2006, 08:55 AM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •