Results 1 to 10 of 10
  1. #1
    Join Date
    Jul 2006
    Location
    Central Mangrove
    Posts
    0

    Default Finishing recycled hardwood

    Our school has just built a deck using rough recycled hardwood.
    The kids are now getting splinters from the seats and rails. I have started sanding the deck, but cant get a splinter free finish. Would a decking oil or a polyurethane finish help.
    regards, clarky

  2. #2
    Join Date
    Jan 2006
    Location
    Melbourne
    Posts
    722

    Default

    What sort of sander are you using? Can you hire a floor sander and give it a really good go?

    I would have thought thats ome thick coats of a sealer should also help. Guess you need to try a section.

  3. #3
    Join Date
    Mar 2005
    Location
    melbourne
    Age
    90
    Posts
    344

    Default

    A standard polyurethane would be no good in a weather prone situation. Wood expands and contracts with wet and sun and polyurethane does not match that kind of movement. That is why, where appearance is important, such as on a boat, spar varnish is used. For outside furniture I use a mix of spar varnish, boiled linseed oil and turps in about one third quantities and find it a very useful wipe on finish.
    In this case perhaps a more oil based oil based finish might be better. Theoretically I know about these finishes but I never give advice unless I have long and practical experience so will stand aside and let others offer advice. However my standard piece of advice is before doing the whole lot, use a piece of scrap for testing.

    Jerry

    War does not decide who is right. War only decides who is left.

  4. #4
    Join Date
    Jul 2006
    Location
    Central Mangrove
    Posts
    0

    Default

    I have a belt sander and will finish with a random/orbital sander. I am not worried about the floor, only the hand rails and the seat that goes around the inside of the deck and is made of 75 x 50 hardwood. I was thinking of using a roundover bit in a router to round off the edges, as some of the worst splinters are along the edges. The oil mixture sounds good.
    regards Clarky

  5. #5
    Join Date
    Mar 2007
    Location
    Canberra
    Age
    73
    Posts
    52

    Default

    Rounding with the router as you suggest or even planing all edges will help greatly. Without a finish your smoothing with machines using bits, blades or paper will last just a short time.

    The tendency to splinter is largely a factor of the wood type, but exposure and weathering that allows drying and lifting of grain worsens any existing tendency and will help splinter formation in all timbers eventually.

    Pretty much any of the commercial oils will help after you have smoothed the surfaces and rounded off edges. In fully exposed situation you will need to re-oil annually at least - perhaps an every spring regime so that best protection is over the summer.

  6. #6
    Join Date
    Jul 2006
    Location
    Central Mangrove
    Posts
    0

    Default

    Thanks for the help, I will get stuck into it when it stops raining
    regards, clarky

  7. #7
    Join Date
    Feb 2006
    Location
    Perth
    Posts
    1,174

    Default

    Quote Originally Posted by clarky View Post
    Our school has just built a deck using rough recycled hardwood.
    The kids are now getting splinters from the seats and rails. I have started sanding the deck, but cant get a splinter free finish. Would a decking oil or a polyurethane finish help.
    regards, clarky
    Paint - sand - paint - paint - paint. Use a thick goopy paint. I've done it and it works

  8. #8
    Calm's Avatar
    Calm is offline Stubby Owner and proud of it. Now coming back to Earth.:D
    Join Date
    May 2006
    Location
    Niddrie, Victoria
    Age
    68
    Posts
    0

    Default

    With the splintery finish on the timber i dont see that oil will help.

    I think you are saying that clothes can catch on the "edges" of the timber - splinters -

    What you need to do is put a finish over the top that will effectively seal/glue/cover these sharps edges to overcome the problem.

    Ideally you need a plasticy type finish that will stand up to the weather - outdoor area - allow movement in the wood, not crack and not get hot and sticky in the summer. You then need to decide if you want to have a clear finish to "show off the timber" or if you are happy to paint it - cover up the timber.

    Oil - will give you some of these but will not give you the plasticy cover to prevent the clothes/skin catching on the "sharp bits"

    2 pack finishes - i dont think these allow for movement in the timber, so will crack and then let the weather in making the proble,m wprse.

    Spa or Marine varnish - i think is the only clear produst for outside that will hopefully give you all that you want but it is fairly expensive and will last a few years

    Plastic outdoor paint is the one that will probably do the lot at the cheapest cost.

    Hopefully this helps. Others feel freee to correct any mistakes i have made, i dont claim to be an expert, just a logical thinker.
    regards

    David


    "Tell him he's dreamin."
    "How's the serenity" (from "The Castle")

  9. #9
    Join Date
    Feb 2003
    Location
    Garvoc VIC AUSTRALIA
    Posts
    3,208

    Default

    The splinters are most likely coming off the corners of the board edges.

    If you put a 45 degree chamfer on all the edge corners then a light rub with sandpaper you should fix it.
    Regards, Bob Thomas

    www.wombatsawmill.com

  10. #10
    Join Date
    Jul 2006
    Location
    Central Mangrove
    Posts
    0

    Default

    Hi
    The splinters are comming from the edges, but also from the rails that are 8" wide and have old nail and screw holes. We would like to be able to see the timber as it has really appealing natural colours. I am worried that a varnish would lift and have to be sanded back and redone every so often. The deck is quite large and I have limited time available and being a public school, limited funds.
    Thanks again Clarky

Similar Threads

  1. filler for recycled hardwood
    By s_m in forum FINISHING
    Replies: 15
    Last Post: 10th June 2007, 11:36 AM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •