Results 1 to 8 of 8
  1. #1
    Join Date
    Apr 2008
    Location
    Armidale
    Posts
    8

    Default Clamps for flooring

    G'day, people,

    I'm going to be putting down my own floor in a few months. I gather you need to clamp them together with a special type of clamp. Anyone know what they're called, where you can get them and what they might cost? Also, how many you might need for 4m long boards? Thanks!

  2. #2
    Join Date
    Jun 2004
    Location
    Grafton, N.S.W.
    Age
    64
    Posts
    546

    Default

    Are you installing secret nail or topnail profile?
    Hooroo.
    Regards, Trevor
    Grafton

  3. #3
    Join Date
    Dec 2005
    Location
    South Australia
    Posts
    140

    Default

    I have always refered to them as floor dogs, I have four, can't tell you where to get them mine came from my grandfather, the ones I have are for top nailing

  4. #4
    Join Date
    Apr 2008
    Location
    Armidale
    Posts
    8

    Default

    Apparently I will not be able to secret nail them as they are 6" wide, and the builder thinks that they will cup if secret nailed. Therefore, they will be top nailed.

  5. #5
    Join Date
    May 2003
    Location
    Kuranda, paradise, North Qld
    Age
    63
    Posts
    2,026

    Default

    You'll need floor clamps, (or dogs) a minimum of three. You should be able to hire them. If possible, get the old fashioned ones which have long handles as it saves a lot of bending down.

    Mick
    "If you need a machine today and don't buy it,

    tomorrow you will have paid for it and not have it."

    - Henry Ford 1938

  6. #6
    Join Date
    Apr 2008
    Location
    Armidale
    Posts
    8

    Default

    Beauty. Thanks, Mick. Will do.

  7. #7
    Join Date
    Jan 2005
    Location
    Sydney
    Posts
    191

    Default

    what is commonly done is the wide board are first secrete nailed with the gun which clamps the boards tight together then after each room is finshed or before the end of the day a caulk line is pulled and the boards are top nailed off.

    we have done this method usin upto 290mm wide boards, if the baords dont pull in tight a chesil can be used to pull it over, the timber milling standards set out the max bow in a board, 90% of the timber boards that are suppiled by a good mill will be pulled tight with just a floor nailer.

    floor clamps can be used the method for these is 6 rows are laid out on the joist or battens then pulled tight with the dogs then nailed off, i dont like this method as when you tighten the dogs the boards tend to lift of the joists.

  8. #8
    Join Date
    May 2003
    Location
    Kuranda, paradise, North Qld
    Age
    63
    Posts
    2,026

    Default

    Quote Originally Posted by Gaza View Post
    ................ i dont like this method as when you tighten the dogs the boards tend to lift of the joists.
    We used to lay a heavy lump of bearer over the top of the joist and stand on it to prevent the flooring popping up and to push it down hard whilst nailing it. Your method of a combination of secret and face nailing sounds good, will mentally file away for future reference.

    Mick
    "If you need a machine today and don't buy it,

    tomorrow you will have paid for it and not have it."

    - Henry Ford 1938

Similar Threads

  1. Sash clamps versus Bessey K series clamps
    By zelk in forum HINTS & TIPS
    Replies: 8
    Last Post: 6th September 2007, 10:24 PM
  2. Replies: 3
    Last Post: 24th June 2007, 03:15 PM
  3. Clamps for direct stick flooring.
    By Miltzy in forum FLOORING
    Replies: 32
    Last Post: 16th September 2006, 06:15 PM
  4. Flooring Clamps
    By Miltzy in forum FLOORING
    Replies: 1
    Last Post: 17th July 2006, 07:47 PM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •