Results 1 to 9 of 9
  1. #1
    Join Date
    Jan 2008
    Location
    melbourne
    Posts
    12

    Default 4.5mm durasheet - ok for wet area tile?

    Hi all,

    I'm renovating my bathroom and being new to the country..(we don't use this stuff where i come from)...i asked my local DIY store for wet area sheets to tile on. They sent me 4.5mm durasheet , is this stuff ok for shower area tiling?
    Thanks for any advice...

    Jim

  2. #2
    Join Date
    Nov 2006
    Location
    Bendigo Victoria
    Age
    80
    Posts
    4,565

    Default

    G'day Jim,

    The manufacturer of Durasheet, BGC, recommends another of their products, Duraliner, in 6mm thickness for wet areas and tiling.

    They recommend Durasheet for external applications.

  3. #3
    Join Date
    Jan 2006
    Location
    Melbourne
    Posts
    722

    Default

    Hi there Jambo000

    Normally 6mm is the go, the 4mm stuff is obviously not as tough, so if you fell agaist the tiled surface it might not stand up so well. Villaboard is anoth 6mm wet area rated product from James Hardie.

  4. #4
    Join Date
    Jan 2008
    Location
    melbourne
    Posts
    12

    Default

    Thanks for the reply's - i'm not worried too much about the strength of the board as i'll be fitted on top of plasterboard. I'm more worried about it's waterproofing abilities. When i removed the existing tiles i found them attached to the same 4.5mm board , they has been there a good few years and appeared to be fine as far as waterproofing is concerned.

  5. #5
    Join Date
    Nov 2003
    Location
    between orange & forbes nsw
    Age
    78
    Posts
    53

    Default

    Hi Jim,
    As the others said 6mm is the go for tiling onto. It is recess edged for flush jointing so you can tile without getting deviation in the tiles on the joint area.

    Good luck
    Bob

  6. #6
    Join Date
    Jan 2006
    Location
    Melbourne
    Posts
    722

    Default

    Note that you still need the correct plaster behind and a waterproof layer over the top. The CS will withstand water without falling apart but it still seeps through ... it isn't a barrier so to speak.

  7. #7
    Join Date
    Aug 2007
    Location
    Noosa Heads
    Posts
    446

    Default

    I have been using Durasheet for the current reno in non critical jobs becuase once the sheet gets wet it has tendancy to shatter and crack. Hardies products are much more durable.

  8. #8
    Join Date
    Jan 2008
    Location
    melbourne
    Posts
    12

    Default

    I've replaced the durasheet with the duraliner instead , reading the specs on their website it makes perfect sense and of course , i don't wanna do this job again! Reference the 'waterproof' layer , what would you recommend i use?

  9. #9
    Join Date
    Jan 2006
    Location
    Melbourne
    Posts
    722

    Default

    I have used http://www.crommelin.com.au/ which you can get from Bunnings. So far it has performed OK.

Similar Threads

  1. Use tile paint or re-tile?
    By Loosescrew in forum KITCHENS, BATHROOMS, THEATRES, etc
    Replies: 5
    Last Post: 18th December 2007, 12:52 PM
  2. Manual Tile Cutter or Electric Tile Saw?
    By Ronaldo451 in forum TILING
    Replies: 10
    Last Post: 22nd November 2007, 09:56 PM
  3. Replies: 0
    Last Post: 21st June 2007, 12:38 PM
  4. Tile Beading.
    By makka619 in forum TILING
    Replies: 3
    Last Post: 9th January 2007, 08:24 PM
  5. Tile Dust
    By Babytoolman in forum TILING
    Replies: 8
    Last Post: 12th April 2006, 06:07 PM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •