Results 1 to 4 of 4
  1. #1
    Join Date
    Sep 2007
    Location
    Armadale
    Posts
    887

    Default Piano finish with a danish oil

    Hi Guys,
    I'm trying to get a hi finish with danish oil (I'm using Cabots) on a small cedar table.
    trouble is there are some really deep grain holes(is this the right word, probably knot)
    After about 4 coats, I got the finish but the grain is still open in a few bits.
    Ive cut back, put a thick coat of DO on, then got inventive

    bubbles were appearing where the holes are, so I got out the hairdryer on low and made up a rubber and attempted to fill the grain as it went tacky.Circular motion.The theory being that the warmth from the dryer would bring bubbles to surface
    then wiped off exess
    I think I filled the gain a bit more but the surface has dulled.

    Question? when this dries will I be able to apply another coat or two to get the shine back and will it be stable?.

    I have never used a grain filler before because I think it muddies the grain a bit , but maybe this time I should have.

    Astrid

  2. #2
    Join Date
    Jun 2006
    Location
    Barboursville, Virginia USA
    Age
    77
    Posts
    549

    Default

    I think a grain filler is your only solution. By that I mean something that dries hard. Danish Oil will never, ever dry hard enough to be used as a filler. It is meant for the excess to be wiped off after each coat.

    You can fill the grain with pore filler or even shellac if not too deep.
    Cheers,

    Bob



  3. #3
    Join Date
    Jan 2002
    Location
    Melbourne, Aus.
    Age
    71
    Posts
    0

    Default

    Maybe try some tinted epoxy next time Astrid.

    As for the dulling, I'd expect another coat would deal with that.

    As for never drying, that would depend on what's in the Cabot's mix.
    Cheers, Ern

  4. #4
    Join Date
    Sep 2007
    Location
    Armadale
    Posts
    887

    Default

    thanks ern ,
    I think it will be ok, Ive a mate who's a proffessional FP and uses this all the time and applys it in much the same way as he does shellac and gets the same finish (well almost)
    but he's an ex weightlifter and has a lot more power and stamina than me!
    and epoxy is such a bugger to sand back.

    thanks bob, cabots isnt a pure oil and hardens up pretty well, just these holes were deeper than usual and I should have filled them first.
    Ill let you know how it goes
    astrid

Similar Threads

  1. Blotchy Danish Oil
    By oldnewbie in forum FINISHING
    Replies: 9
    Last Post: 18th September 2007, 04:23 PM
  2. Wax & Danish Oil
    By Ausworkshop in forum FINISHING
    Replies: 4
    Last Post: 23rd August 2007, 06:07 PM
  3. stain and danish oil
    By reo in forum FINISHING
    Replies: 5
    Last Post: 2nd February 2006, 11:29 PM
  4. EEE Ultra shine + danish oil + shellawax cream
    By EMistral in forum FINISHING
    Replies: 4
    Last Post: 29th September 2005, 10:13 PM
  5. danish oil
    By jow104 in forum FINISHING
    Replies: 1
    Last Post: 20th July 2003, 12:13 PM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •