Results 1 to 15 of 27
Thread: Gpo In Bathroom
-
21st September 2007, 02:06 PM #1Member
- Join Date
- Feb 2007
- Location
- WA
- Posts
- 45
Gpo In Bathroom
Just wondering if there is a minimum distance above a bathroom vanity required for a new power outlet. I currently have 100mm but need to drop it down due to buying a larger than thought mirror.
Regards
Greg
-
21st September 2007, 03:02 PM #2
Greg the GPO is not allowed within an area 400mm above and 150mm to the sides of the basin.
Check with your electrician before attaching the mirror.Those were the droids I was looking for.
https://autoblastgates.com.au
-
21st September 2007, 03:21 PM #3
I was under the impression that it was 600mm from any water source??
Too many projects, so little time, even less money!Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds! Doing work around the home? Wander over to our sister site, Renovate Forum, for all your renovation queries.
-
21st September 2007, 03:27 PM #4
-
21st September 2007, 11:52 PM #5
NCarcher is spot on..
-
22nd September 2007, 08:20 AM #6Electrician
- Join Date
- Sep 2007
- Location
- Thailand
- Age
- 63
- Posts
- 90
As already suggested, this is not permitted unless other conditions have been met. Below is the AS/NZS 3000:2000 ruling. I have bolded the important parts. To further clarify, you wish to install a GPO in 'zone 2'.
7.1.4.2 Socket-outlets.
Socket-outlets shall not be installed within 0.3 m of the floor of a bathroom,laundry or other similar location where the floor is likely to become wet.
In addition, and regardless of the degree of protection provided by the equipment, the following conditions shall apply to the installation of socketoutlets in the classified zones:
(a) In Zones 0 and 1 socket-outlets shall not be permitted.
(b) In Zone 2, socket-outlets shall not be permitted unless they—
(i) have automatic switching and are incorporated in a shaver supply unit complying with AS/NZS 3194; or
(ii) are protected by a RCD with a maximum rated residual current of 30 mA; and
(iii) are enclosed in a cupboard provided that the enclosure is maintained during the normal operation of the connected equipment.
In summary, the only way that you can install a GPO in the location that you wish, is to make sure that it is RCD protected AND it is enclosed in a cupboard provided that the enclosure is maintained during the normal operation of the connected equipment.“I do not think there is any thrill that can go through the human heart like that felt by the inventor as he sees some creation of the brain unfolding to success... Such emotions make a man forget food, sleep, friends, love, everything.” - Nikola Tesla.
-
25th September 2007, 02:09 PM #7Member
- Join Date
- Feb 2007
- Location
- WA
- Posts
- 45
Is that right. I have two bathrooms in our new house and they both have power outlets above the vanity basin to the side. They are all RCD protected. Does this mean they are illegal? The electrician put them there!
Greg
-
25th September 2007, 02:24 PM #8SENIOR MEMBER
- Join Date
- Aug 2002
- Location
- Boyne Island, Queensland
- Age
- 52
- Posts
- 176
How far to the side of the basin are they?
Dan
-
25th September 2007, 04:58 PM #9wannabe woodworker
- Join Date
- Aug 2007
- Location
- Yanderra nsw
- Posts
- 28
i am looking at the pic in AS:3000 right now and as said if the capacity is less than 45L it must be 400mm above or 150mm to the side(this is to the closest edge of the GPO.
Hope that helps.
-
25th September 2007, 05:02 PM #10wannabe woodworker
- Join Date
- Aug 2007
- Location
- Yanderra nsw
- Posts
- 28
My rules say they are not permitted in zone 0,1 or 2 at all only in zone 3 which is outside above measurements
-
25th September 2007, 06:24 PM #11SENIOR MEMBER
- Join Date
- Aug 2002
- Location
- Boyne Island, Queensland
- Age
- 52
- Posts
- 176
-
25th September 2007, 06:35 PM #12Member
- Join Date
- Feb 2007
- Location
- WA
- Posts
- 45
It is a 1200mm vanity so the power point would be approx 500mm to one side and up 100mm from the vanity top. I've seen it heaps of times before. There must be another clause. Maybe Santa can help.
-
25th September 2007, 06:50 PM #13Electrician
- Join Date
- Sep 2007
- Location
- Thailand
- Age
- 63
- Posts
- 90
As per AS/NZS 3000:2000, purchased 2006, with amendments 1,2 & 3, Fig 7.1C(a) & Table 7.1;
I'll have to do this in 2 separate posts...file size too big.“I do not think there is any thrill that can go through the human heart like that felt by the inventor as he sees some creation of the brain unfolding to success... Such emotions make a man forget food, sleep, friends, love, everything.” - Nikola Tesla.
-
25th September 2007, 06:54 PM #14Electrician
- Join Date
- Sep 2007
- Location
- Thailand
- Age
- 63
- Posts
- 90
Here is the next pic...had to change to GIF.
Also, this may help;
7.1.2.2 Other fixed water containers.
The requirements for fixed water containers other than baths and showers are based on the dimensions of the following two zones (examples are given in Figure 7.1C):
(a) Zone 0 shall be the area of the interior of the water container.
(b) Zone 2 shall be—
(i) for individual water containers with a capacity not exceeding 45 L, the area limited by—
(A) the vertical plane 0.15 m from the internal rim of the water
container; and
(B) the floor and the horizontal plane 0.4 m above the water
container; and
NOTE: Figure 7.1C(a) shows a typical double bowl sink where the capacity of each container does not exceed 45 L.
(ii) for water containers with a capacity exceeding 45 L, the area limited by—
(A) the vertical plane 0.5 m from the internal rim of the water
container; and
(B) the floor and the horizontal plane 1.0 m above the water
container.
NOTES:
1 There are no Zones 1 or 3 associated with these water containers.
2 The zones do not extend beyond the boundaries of the room.“I do not think there is any thrill that can go through the human heart like that felt by the inventor as he sees some creation of the brain unfolding to success... Such emotions make a man forget food, sleep, friends, love, everything.” - Nikola Tesla.
-
25th September 2007, 10:17 PM #15
Whatt??
Uhuh, so now I really understand! Can I really have a powerpoint in the bathroom I am currently building or should I just run an extension lead out the door?
Similar Threads
-
Bathroom Renovation Project
By juan in forum BATHROOM & TOILETReplies: 152Last Post: 3rd May 2008, 04:58 PM -
Complete Bathroom in a Day
By batcat in forum BATHROOM & TOILETReplies: 3Last Post: 31st January 2007, 12:41 PM -
How to most out of a Small bathroom?
By Ayesha in forum KITCHENS, BATHROOMS, THEATRES, etcReplies: 13Last Post: 21st August 2006, 08:17 PM -
Installing GPO in cupboard
By Trav in forum PLUMBING, ELECTRICAL, HEATING, COOLING, etcReplies: 12Last Post: 16th January 2006, 04:53 PM
Bookmarks