Results 1 to 7 of 7
  1. #1
    Join Date
    Nov 2004
    Location
    Eastern Suburbs Melbourne
    Posts
    0

    Default Angles for window beading

    I'm looking at using some beading on the outside of some windows to hold glass in (rather than putty). Had a look at a friend's, I couldn't work out what angle to cut the strips. They're not 45 degs, some type of compound angle I guess. What sort of angle should I use for a neat joint? Thought a coping joint might be the go but a bit confused when I saw what was on my friend's window.

  2. #2
    Join Date
    Oct 2006
    Location
    Tallahassee FL USA
    Age
    82
    Posts
    0

    Default

    Are we talking about quarter-round moulding? Sometimes not exactly symmetrical, i.e. more like a quarter ellipse. If improperly installed, an awkward miter would be required. If you mark one back face before cutting to length, you can keep proper orientation all around and use a regular 45 degree miter.

    Joe
    Of course truth is stranger than fiction.
    Fiction has to make sense. - Mark Twain

  3. #3
    Join Date
    Nov 2004
    Location
    Eastern Suburbs Melbourne
    Posts
    0

    Default

    Joe, the stuff that I've seen is not rounded but bevelled outwards, I guess to provide water run-off.

  4. #4
    Join Date
    Oct 2006
    Location
    Tallahassee FL USA
    Age
    82
    Posts
    0

    Default

    OK, Tiger. But if the same cross section is used all around, an awkward miter should be needed only if the cross section has unequal leg lengths, and one or more pieces is installed barse ackwards. The trick of marking the back face before cutting should still permit 45 degree miters. If you're using different cross sections for top, sides and bottom, or if one or more pieces is deliberately set awry, an entirely different situation. Only the bottom piece would need a water-shedding bevel, and a film of sealant under all pieces is advisable. Perhaps a pic of your friend's installation would illuminate things.

    Joe
    Of course truth is stranger than fiction.
    Fiction has to make sense. - Mark Twain

  5. #5
    Join Date
    Jul 2006
    Location
    Raymond Terrace
    Posts
    0

    Default

    Quote Originally Posted by Tiger View Post
    I'm looking at using some beading on the outside of some windows to hold glass in (rather than putty). Had a look at a friend's, I couldn't work out what angle to cut the strips. They're not 45 degs, some type of compound angle I guess. What sort of angle should I use for a neat joint? Thought a coping joint might be the go but a bit confused when I saw what was on my friend's window.

    Your not the only one confused. Not totally clear on what you are asking so I will answer all possibilities.

    Sound to me like you are 'replacing' the putty with a timber bead insert and a bit of silicone.

    Assuming you are asking about the angle of the face of the insert, that will be determined by your window sash.
    Lets say
    Rebate in sash is 8mm wide.
    Glass is 3mm thick.
    Glass rebate in sash is 15mm deep

    ....(15 - 3 = 12mm. Cross section of bead would be right angle triangle with 8mm base and 12mm high. (although you would probably leave a small flat on top) A little maths and you come out with an angle of 56.3*. Or if you want to do it the easy way draw up the triangle ( measurements scaled up by a factor by 10 for ease of drawing) and measure angle.

    A coped joint is the 'standard' for most structural joinery. Since you are working with a triangle mould the cope could be easily cut on drop saw. It would be a simple angle and not a compound angle. It would simply be the complementry angle to the face of the mould. ( 90 - 56.31 = 33.69*) A coped joint would look like it was mitred if fitted properly

    The only time a mitre joint will vary from 45* is if you are fitting out an irregular shaped frame like a rhomboid / octagon/ triangle.

    Hopefully that helps to clear it up ... or confuse you more
    Every hour, every day I'm learning more
    The more I learn the less I know about before
    The less I know the more I want too look around
    Digging deeper for clues on higher ground.

  6. #6
    Join Date
    Jul 2004
    Location
    Sale
    Age
    69
    Posts
    559

    Default

    Tiger,

    I've recently cut some beading to match some damaged stuff on a Stegbar window. I used a 15 degree router bit and ran a bit of sand paper over the piece to slightly round and relieve the edges. Seemed to match well enough and I hope this goes someway to answer your question.

    Cheers, John.

  7. #7
    Join Date
    Nov 2004
    Location
    Eastern Suburbs Melbourne
    Posts
    0

    Default

    Thanks, guys, you may have given me what I need. If still a problem, I will get a photo for you.

Similar Threads

  1. Tile Beading.
    By makka619 in forum TILING
    Replies: 3
    Last Post: 9th January 2007, 08:24 PM
  2. Installing beading Help!
    By Tiger in forum DOORS, WINDOWS, ARCHITRAVES & SKIRTS ETC
    Replies: 0
    Last Post: 9th January 2005, 09:07 AM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •