Results 1 to 8 of 8
  1. #1
    Join Date
    Feb 2007
    Location
    Sydney
    Posts
    87

    Post Silver soldering 3/4 inch pipe with MAPP gas

    I've read most of the threads on silver soldering and some suggest that it is possible to silver solder 3/4 inch pipe, but I'm still having problems getting enough heat into the fitting for the solder to flow. I'm attempting to join two 6m lengths of 3/4 inch type B copper pipe with a 8000 TS (from memory) MAPP gas torch. One of the pipes is mostly buried in the ground.

    I can successfully join 1/2 inch pipe and I was wondering what I can do to get more heat into the joint?

  2. #2
    Join Date
    Sep 2006
    Location
    Avoca Victoria
    Age
    81
    Posts
    7,790

    Default

    G'day,
    Probably pushing the BTU limits, but maybe a bit of excavation around the buried pipe and some heat sinks around the area.....like fire bricks or similar. I know from experience that house bricks go bang when they get hot enough.
    Lots of cleaning/good flux, and good luck

  3. #3
    Join Date
    Dec 2006
    Location
    Canberra
    Age
    45
    Posts
    93

    Default

    Quote Originally Posted by emptybucketman View Post
    I've read most of the threads on silver soldering and some suggest that it is possible to silver solder 3/4 inch pipe, but I'm still having problems getting enough heat into the fitting for the solder to flow. I'm attempting to join two 6m lengths of 3/4 inch type B copper pipe with a 8000 TS (from memory) MAPP gas torch. One of the pipes is mostly buried in the ground.

    I can successfully join 1/2 inch pipe and I was wondering what I can do to get more heat into the joint?
    Try and point the flame along the pipe not across it and not too close. you will see the tail of the flame start to change colour when it starts getting hot.

    It might take a bit of practice to work out the best angle to hold it.

  4. #4
    Join Date
    Apr 2006
    Location
    Sydney, Australia
    Posts
    0

    Default

    It can be done. I have just replace my hot water system. (this is what stopped me going to the woodworking show as it took all my spare cash )

    I had to silver soldier one of the joints as it kept on leaking with soft soldier. I bought MAP just for the job and got it red hot and the silver soldier went straight on, with flux of course. Your problem maybe water in the pipe, if you can eliminate this you shouldn't have a problem.

    Squirrel.

  5. #5
    Join Date
    Feb 2007
    Location
    Sydney
    Posts
    87

    Question

    Maybe I have the torch too close since the tip of the flame is nearly two inches from the nozzle. There was a little condensation in the buried pipe but it hasn't been used only buried.

    Would a heat shield attachment make the difference?

    Watson...Where can I get the fire bricks? I presume these are bricks for kilns and fireplaces.

  6. #6
    Join Date
    Sep 2006
    Location
    Avoca Victoria
    Age
    81
    Posts
    7,790

    Default

    I reckon you can get firebricks at one of those Coonara places.

  7. #7
    Join Date
    Dec 2006
    Location
    Canberra
    Age
    45
    Posts
    93

    Default

    A bit of fibre cement sheeting can be very useful as a heat shield.

    No need for flux if joining clean copper but you need it if joining to brass etc.

  8. #8
    Join Date
    Jul 2007
    Location
    Sydney-south
    Posts
    333

    Default

    Cleanliness is next to godliness, use flux if necessary, make sure there is NO water in the pipe at all, dont use the tip of the mapp use the start of the flame and try a stick of 15% silver solder, youll be surprised.

Similar Threads

  1. can mapp gas silver solder
    By davo_scuba in forum PLUMBING, ELECTRICAL, HEATING, COOLING, etc
    Replies: 15
    Last Post: 10th February 2007, 11:28 AM
  2. How to do reliable silver soldering
    By Arron in forum PLUMBING, ELECTRICAL, HEATING, COOLING, etc
    Replies: 11
    Last Post: 23rd May 2005, 11:19 AM
  3. Replies: 1
    Last Post: 28th May 2003, 12:59 AM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •