Results 1 to 10 of 10
Thread: Mould stains - how to remove
-
25th August 2006, 09:58 AM #1
Mould stains - how to remove
Hi,
I have a camphor laurel slab which has some mould stains on it. The timber is now dry, i think that the mould probably happened when it was first cut, maybe the slabs were stacked together. I have seen a similar thing in a peppercorn burl which I cut.
It appears as dirty greyish spots about 3-mm, spattered across the wood. I removed an extra 3mm of wood but they go quite deep.
Is there anything I can use before finishing with hard Shellac, which will fade these spots without wrecking the timber?Cheers,
Steck
-
25th August 2006, 03:06 PM #2SENIOR MEMBER
- Join Date
- Aug 2005
- Location
- kiama
- Posts
- 390
Try a bit of bleach, its about the only thing that will kill mould. as it may change the colour if too strong weaken it down and just do a small area first so you can gauge the results.
I had seveal hides of leather given to me which were mouldy, one dose of bleach and they have never come back.
-
25th August 2006, 09:49 PM #3
Blue stain usually goes very deep into the timber.
You will probably need a very strong bleach like Oxalic acid to remove them, but it will lighten all of the timber not just the blue stained section.
-
26th August 2006, 10:01 PM #4
Per Bob I'd try a oxalic acid solution as well.
Cheers................Sean
The beatings will continue until morale improves.
-
26th August 2006, 10:28 PM #5
Just been plugging some misaligned holes with fiji mahogony. Wiped off the glue with a damp cloth and 5 mins later there was dark blue spots all over the place. This particular piece must be full of spores. I cleaned up another piece we use for a chopping board with bleach. Killed the mould but it looks awful now. I wouldnt put bleach on a piece I was using for a feature.
Is oxalic acid better??
Where do you get it??
what about into the microwave for a minute or two??
that should kill the little buggers......ray c
dunno what's more fun, buyin' the tools or usin' em'
-
26th August 2006, 11:18 PM #6
Ray, I'm not a chemist but oxalic acid is a very different beastie to chlorine bleach.
Most paint suppliers will have it for cleaning/rejuvenating old timber.
Another thought is to try an oxygen bleach product such as napisan or a generic cheaper version, once again a different beast to chlorine bleach.
Cheers..................Sean
The beatings will continue until morale improves.
-
27th August 2006, 09:44 AM #7
I will do a test on a spare piece of offcut. I have already found out that the stain goes along the grain and through the whole piece of timber, so I only expect to affect the surface layer. If this doesn't work, I may have to try hiding the stains. The wood has plenty of dark feature, so I could cut off the lighter wood, but I love the contrast. Thanks for the suggestions. I will let you know the results.
Cheers,
Steck
-
30th August 2006, 07:51 PM #8
Test Results to remove mould stains
Well I put the mould removing suggestions to the test.
This is the original piece of timber
Attachment 29376
This is what it looks like wet with water. It loooks worse wet with turps!
Attachment 29381
As you can see from this edge view, the mould goes deep and has penetrated right through the slab.
Attachment 29378
I treated one section with undiluted dishwashing detergent.
The next I treated with undiluted bleach (White King).
The next section was done with with Oxalic acid solution.
And then I just Karchered the last section.
All the chemicals were vigorously scrubbed and let to stand for 10 minutes.
THe results are:
Attachment 29380
The detergent was useless. The bleach produced the best improvement but still far from perfect. The Oxalic Acid made some improvement and the Karcher had no effect.
The bleach had the best effect and If I left it longer or used a stronger bleach it might produce an acceptable result.
I am led to ask, If I used the bleach, would it have a negative effect on my final finish?
What do you think of the idea (if more bleaching fails, as I think it will) of staining the sapwood a darker color?Cheers,
Steck
-
31st August 2006, 08:48 PM #9
Steck, the bleach you tried (white king) is chlorine bleach, per my post I'd give oxygen bleach (napisan, etc) a shot at it.
Cheers.............Sean
The beatings will continue until morale improves.
-
31st August 2006, 10:20 PM #10
I will give the oxygen bleach a go. I just didn't have any at the time.
Thanks for your interest.Cheers,
Steck
Similar Threads
-
mould proof silicone
By sandrandave in forum KITCHENS, BATHROOMS, THEATRES, etcReplies: 12Last Post: 14th August 2006, 10:27 AM -
Easy way to remove palms
By arose62 in forum BRICKWORK, CONCRETING, PAVING, RENDERING, etcReplies: 18Last Post: 13th December 2004, 10:11 AM -
Stains on Deck
By Old Harry in forum DECKINGReplies: 2Last Post: 13th April 2004, 12:09 PM -
Water Stains on Oak Cabinet - How to remove?
By Jules in forum FINISHINGReplies: 0Last Post: 16th January 2004, 09:02 AM
Bookmarks