Results 1 to 9 of 9
  1. #1
    Join Date
    Feb 2006
    Location
    Perth
    Posts
    1,174

    Default TS guard - something different

    Because I often cut rebates etc and operate quite a bit without the standard TS blade guard I've been thinking for a while about a more flexible guard. I've thought about making one of those scissor action drop down from the ceiling guards/units but also thought there must be a simpler way. So, after purchasing a dust picker on special from timbecom, and finding a sheet of 1mm polycarbonate sheet smeared with silicone rubber at work that no one looked like they wanted, I came up with the following (photo 1).

    The polycarbonate is thin enough that it will bend fairly nice and squarely provide you apply significant force (you really have to over bend it) but it's so tough that it does not snap or break. I basically cut and folded the poly into a cowl in such a way that it fits over the top of black plastic dust picker cowl. Then I pop rivetted the poly to itself and bolted the poly cowl to the dust picker. As you can see, the blade visibility is very high even with the guard fully lowered.

    The dust picker arm is bolted to a wall stud and I also inserted a large polyethylene washer into the first dust picker's serrated joint so that the picker can turn more freely (but not loosely) in the horizontal plane. (see photo 4)

    Photo 3 shows the guard pulled up out of the way. It will go up a little more than what I have shown there.
    The guard can be raised and lowered above the saw bench using a nylon rope and a spring clamp which holds the rope to a Z beam on the ceiling (see photo 4). NB: This is only a temporary setup until I get some stainless steel cable and a couple of pulleys and something more positively locking than a spring clamp.

    So far it works as expected and certainly makes me feel a bit safer around that blade. The hardest parts were getting the silicone off the poly and marking and cutting the poly cowl shape out in one piece. Had to recall all my high school geometry out for that one!

    Oh yeah and one more thing, it has enough extension left in it's joints etc to swing out over the bench and still act as a regular dust picker.

  2. #2
    Join Date
    Jun 1999
    Location
    Westleigh, Sydney
    Age
    78
    Posts
    1,332

    Default

    Very clever idea Bob. Have a greenie.
    Visit my website
    Website
    Facebook

  3. #3
    Join Date
    May 2005
    Age
    72
    Posts
    36

    Default

    Well done. Nice and simple and effective.

  4. #4
    Join Date
    Feb 2006
    Location
    Perth
    Posts
    1,174

    Default

    Thanks guys.

    This evening I replaced the temporary nylon cord with a stainless steel cable and pulley/counterweight (using 2L bottle of water) system. Guard sits at whatever height I place it. Now I think it needs a handle at the front - maybe tomorrow night.

    Cheer

  5. #5
    Join Date
    Jul 2005
    Location
    Oberon, NSW
    Age
    64
    Posts
    0

    Default

    Nice idea, Bob!

    Just curious, you notice any loss of suction having the flex-duct coiled that way?
    I may be weird, but I'm saving up to become eccentric.

    - Andy Mc

  6. #6
    Join Date
    Feb 2006
    Location
    Perth
    Posts
    1,174

    Default

    Quote Originally Posted by Skew ChiDAMN!!
    Nice idea, Bob!

    Just curious, you notice any loss of suction having the flex-duct coiled that way?
    Amazingly it's only 3% loss for 3 x 360 degree turns - I still can't believe it either. Mind you because of the effect of dust bag blockage and ducting losses this is when operating at around 250 cfm - it would probably be much more at higher flow rates

    My fluid mechanics boffins at work tell me a smooth spiral is not so bad for fluid flow, its when going from straight to curved and back again or changing the curvature that you get problems.
    Cheers

  7. #7
    Join Date
    Nov 2003
    Location
    Sydney
    Age
    54
    Posts
    891

    Default

    Good work Bob. I have something similar and it is a bit more home-made. It makes such a big difference when doing a lot of ripping. There is no dust, it is protective and I don’t have to wear goggles.

    http://www.woodworkforums.ubeaut.com...6&d=1137070174
    Visit my website at www.myFineWoodWork.com

  8. #8
    Join Date
    Feb 2006
    Location
    Perth
    Posts
    1,174

    Default

    Quote Originally Posted by Wongo
    Good work Bob. I have something similar and it is a bit more home-made. It makes such a big difference when doing a lot of ripping. There is no dust, it is protective and I don’t have to wear goggles.

    http://www.woodworkforums.ubeaut.com...6&d=1137070174
    Nothing wrong with home made and was thinking along the same lines as your design when I was browsing through the timbecon catldog and my idea hit me. Anyway, I really like your setup - so much spaaaace especially on the walls! What's the big wooden block at the front of the saw sled for, is it just for protection or something else?

  9. #9
    Join Date
    Nov 2003
    Location
    Sydney
    Age
    54
    Posts
    891

    Default

    Quote Originally Posted by BobL
    What's the big wooden block at the front of the saw sled for, is it just for protection or something else?
    Protection
    Visit my website at www.myFineWoodWork.com

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •