Results 1 to 5 of 5
  1. #1
    Join Date
    Aug 2020
    Location
    Wollongong, NSW
    Posts
    11

    Default Wax stain removal

    Hi Guys/Girls,
    While fitting the hardware to a recently completed box, I managed to get some wax on the unfinished timber (Camphor Laurel). Before I just make things worse, can anyone give me some pointers on how I might remove this?
    All help greatly appreciated.

  2. #2
    Join Date
    Apr 2014
    Location
    Kew, Vic
    Posts
    123

    Default

    My go-to for wax removal is Liberon Wax and Polish remover. It should be readily avaiable in the UK. These instructions are from an Aussie website:

    ———————————————————

    How to use
    Application
    For best results soak a pad of Liberon Ultra Fine Steel Wool (grade 0000) in Wax and Polish Remover, squeeze out the excess and working on a small area at a time, gently wash the surface going with the grain where possible.
    Allow a few minutes for the Wax and Polish Remover to work, then while the surface is still wet use a clean lint-free cloth to wipe off all the old softened wax.
    Repeat this process until all the old wax is removed. Allow 24 hours for the treated surface to dry completely before re-finishing.

    Important: This product may damage newly applied French polishes, lacquers, varnishes and sealers. Always test product on a spare surface or inconspicuous area for colour, compatibility and end result.

    Precautions
    Wear suitable heavy duty gloves. Do not pour into plastic containers or use on plastic or vinyl surfaces. Dispose of used steel wool and cotton cloths outside to reduce vapour build-up and fire hazard. Do not use on water-based varnish.

    ——————————————————

    Lots of other wax removers online but this is the only one I’ve used.

    Good luck. If you get a chance please let us know how it goes.

    Best regards,

    Brian

  3. #3
    Join Date
    Aug 2020
    Location
    Wollongong, NSW
    Posts
    11

    Default

    Thanks Homey
    I didn't mention in the original post that it is only a couple of small spots from the wax that I use on the screws and, as I'll be using a wipe-on Poly, do you think that the wax that may not come out will affect the finish?

  4. #4
    Join Date
    Apr 2014
    Location
    Kew, Vic
    Posts
    123

    Default

    Hi Luckyb,

    If it’s just a few spots I’d probably try brown paper and a warm iron first just to soak up whatever I could, then try mineral turps on a cotton bud. I’m not a professional, though, so if you hang on a bit I’m sure someone with more specialist knowledge will be along to advise you.

    Best regards,

    Brian

  5. #5
    Join Date
    Aug 2020
    Location
    Wollongong, NSW
    Posts
    11

    Default

    Thanks Homey
    I agree with your suggestions and will also wait a bit before I try anything.

Similar Threads

  1. pork fat stain removal
    By Shedhand in forum RESTORATION
    Replies: 5
    Last Post: 27th September 2021, 07:22 PM
  2. Replies: 3
    Last Post: 6th January 2019, 05:20 PM
  3. Bore stain removal, is it possible?
    By Malperth in forum NOTHING AT ALL TO DO WITH RENOVATION
    Replies: 8
    Last Post: 12th October 2008, 10:14 PM
  4. Removal Of Stain From Fingers - Help !
    By Sorehorse in forum FINISHING
    Replies: 19
    Last Post: 5th November 2005, 01:28 PM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •