Results 1 to 15 of 17
Thread: Sharpie on garden labels
-
13th November 2022, 02:40 PM #1Intermediate Member
- Join Date
- Jul 2022
- Location
- Gympie, QLD
- Posts
- 10
Sharpie on garden labels
I've made some garden labels from hardwood. Then I carved the names of the plants with a rotary tool.
I plan to finish them with a mineral spirits + linseed oil + paraffin wax solution. (Plus a creosote type product for the bit that goes into the soil.)
The names need to be darker to be legible. I tried a pyrography pen/tool, but it took far too long.
I'm wondering if I use a Sharpie (texta/marker) and cover it with the proposed finish, above, will the ink bleed over time when exposed to the elements.
(I did a couple of test pieces and the ink didn't bleed at all -- like I thought it would -- but I'm not sure how it'll hold up over time.)
I've got a hundred or more to do and I'm trying to avoid having to re-do them in six months.
Whaddyareckon?
-
13th November 2022, 03:55 PM #2Senior Member
- Join Date
- Jun 2017
- Location
- Western Australia
- Posts
- 69
A Sharpie is likely to fade in the sun - paint markers are likely to handle the UV better.
-
13th November 2022, 04:08 PM #3GOLD MEMBER
- Join Date
- Apr 2019
- Location
- NSW
- Age
- 38
- Posts
- 309
can you just use a normal exterior paint and a small brush?
other option that may take a little bit longer (or shorter) would be to spray paint the whole label after you've cut the lettering and then just quickly sand it again to expose the wood
3rd option would be to make all the signs up, lay them down, mix up a batch of the cheapest epoxy you can find and dye it black and just pour it into each letter, at least it would level out in the lettering and a jumbo syringe would avoid spills and probably go pretty quick
-
13th November 2022, 05:09 PM #4Intermediate Member
- Join Date
- Oct 2022
- Location
- Canberra
- Posts
- 10
A somewhat unusual suggestion...
Hi TryingItAtHome,
While I agree with the other response about exterior paint in that it will be less likely to fade. May I humbly suggest the somewhat maligned (and forgotten) art of pyrography?
Since it burns/writes into the wood, you know it won't fade, and doesn't really need any additional carving steps. Obviously, you also won't have any paint/brushes to buy. If you have a lot of labels to do, it may actually come out cheaper, easier, (and less messy) than buying paints/brushes/cleaning stuff. Carbatec sells pyrography pens for as little as $80 (probably even cheaper on AliExpress/eBay) and with a little practice, should have little difference from writing with a sharpie.
Anyway, just some food for thought...
Hamish.
-
13th November 2022, 05:42 PM #5GOLD MEMBER
- Join Date
- Apr 2014
- Location
- Little River
- Age
- 78
- Posts
- 225
I think that you have found the perfect justification to lash out and buy a small CNC to engrave your labels.
If you engrave slow enough the cutter will burn the timber and the label is ready.
-
13th November 2022, 09:49 PM #6Intermediate Member
- Join Date
- Jul 2022
- Location
- Gympie, QLD
- Posts
- 10
-
13th November 2022, 09:52 PM #7Intermediate Member
- Join Date
- Jul 2022
- Location
- Gympie, QLD
- Posts
- 10
i appreciate all the other suggestions, too; they're awesome! I'll see how I go. I might combine two ideas: apply exterior paint with a small brush and then give it a light sand anywhere I've coloured outside the lines.
(I'll also check out the pyrography kits from Carbatec. The one I was using was just a cheapie so perhaps that was the issue.)
Thanks very much!
-
13th November 2022, 09:54 PM #8GOLD MEMBER
- Join Date
- Apr 2014
- Location
- Little River
- Age
- 78
- Posts
- 225
I'm sure you need some kitchen items engraved.
-
14th November 2022, 09:48 AM #9
Try oiling your timber first before carving out the name; then you can daub paint into the carving and immediately wipe off the excess with a cloth wrapped around a firm-ish block of rubber or cork. This will work best if the wood has a smooth flat surface such as gained by planing rather than sanding unless you were planning to sand to about 400 grit! Once the paint has dried slap on another oil coat.
If you have a cheap and nasty block plane that you care little about you could skip the initial oil coat and simply fill the carving with paint then give a couple of swipes with the plane after it has dried; but this will likely smear hardened-but-still-softish paint over the sole and blade requiring frequent removal.Nothing succeeds like a budgie without a beak.
-
14th November 2022, 01:29 PM #10
TIAH
In post #2 mpot mentioned a Sharpie would fade and that you could try a paint marker. I fully agree that the Sharpie would not last any time at all (I think even rain would dissolve it). I am not sure how paint markers would go long term, but there is another pen that farmers use to write on the ear tags for their livestock. My experience of these is that they last for longer than the animal itself (assuming that it is a cow rather than a steer ) and are more indelible than even the paint markers. However, they are used on a polythene type plastic and I don't know how they go on timber. Possibly one of the forum farmers could offer some experience here.
If it works, it would be both quicker and cheaper than almost any option so far made. They can be purchased from the farm supply stores or stock and station agents. I am sure Gympie would have several (agents not pens ).
Regards
PaulBushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
-
14th November 2022, 09:03 PM #11GOLD MEMBER
- Join Date
- Apr 2019
- Location
- NSW
- Age
- 38
- Posts
- 309
they're just paint pens
Allflex Tag Pen | Black or White, Broad & Fine Tip | Specialist Sales
-
15th November 2022, 08:41 AM #12
HAB
It is now more than twenty years since I used those pens, but that was the brand I remember. They seemed different to the paint markers in the way they performed as I did use the paint markers once when I ran out of the Allflex thinking it was the same stuff. It seemed different, however, I can't be sure of my assessment.
It would certainly be relatively easy to try, but it would take a couple of years to see if they retained their clarity.
Regards
PaulBushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
-
17th November 2022, 10:27 AM #13
Stupid idea that may work well.
Paint the labels a dark colour and leave the lettering unpainted.
The hard wood over time even with your finish on it is going to go silver to grey in colour making it harder to read the letters anyway.
Cheers - Neil
PS they're plant labels, how long do you expect them to last. I doubt the finish you propose to use will last very long.
-
17th November 2022, 09:51 PM #14GOLD MEMBER
- Join Date
- Apr 2019
- Location
- NSW
- Age
- 38
- Posts
- 309
-
23rd November 2022, 09:58 PM #15Intermediate Member
- Join Date
- Jul 2022
- Location
- Gympie, QLD
- Posts
- 10
Thanks, Neil. I like this contrarian way of thinking.
I'm keen to know more about this; it's the reason I originally posted this in the Finishing board. I know diddly about finishes and the "recipe" I have is:
- 4L mineral spirits
- 1L boiled linseed oil
- 200g paraffin wax. Melt using double-boiler. Mix in 10L bucket with other ingredients.
Bookmarks