Results 1 to 9 of 9
Thread: Water stain
-
19th November 2005, 01:55 AM #1
Water stain
Some years ago a made a hall table from Tasmanian Oak inlaid with strips of Myrtle and Huon Pine. I finished it with Organoil (I think).
My better half put a favourite pot plant on the table and it grew there happily for about 6 years. When we sold up and moved we lifted the pot plant and bowl and discovered to our horror that at some stage the water bowl had overflowed and there was a filthy big round water stain in the timber (not the Huon Pine though). When I got my Shed (pictured at left ) set up I began the process of removing the stain. I tried everything except the belt sander - an option that's not an option . Steel wool and metho, wet and dry with water and metho, Bleach (left overnight). I managed to get the stain to fade to about 50% thanks to the bleach, though any part of the chemical cocktail could have been responsible. I've considered routing the circle stain (about 200mm diameter) and inlaying Huon Pine or King Billy. Before I undertake this option is there anything else people can recommend for removing the water stain.
Ta! :confused:If you never made a mistake, you never made anything!
-
19th November 2005, 07:15 AM #2
Absolutely no problem - put the pot plant back
If at first you don't succeed, give something else a go. Life is far too short to waste time trying.
-
19th November 2005, 07:25 AM #3Senior Member
- Join Date
- Mar 2004
- Age
- 77
- Posts
- 151
Liberon Enterprises (www.liberon.com.au) sells Wood Bleach -
"For removing dark stains caused by rust, alcohol, damp, ring marks, fruit etc., and lightening naturally dark wood or natural wood which has darkened through alkali stripping, staining or weathering."
I suppose any wood bleach would do the job.
-
19th November 2005, 05:59 PM #4
Hmmm....
Originally Posted by Gumby
If you never made a mistake, you never made anything!
-
19th November 2005, 06:00 PM #5
Thanks
Originally Posted by wombat47
CheersIf you never made a mistake, you never made anything!
-
22nd November 2005, 11:29 PM #6
Water Stains
Ok Guys, 'ere 'tis,
Mixture:
250 grams of Oxalic Acid fully disolved in 2 litres of water.
--------Oxalic acid is one of the strongest organic acids. It is widely used in wood restorers and deck cleaners to dissolve the top layer of dried wood and expose a clean layer-----
NOTE: It is a poisonous substance its fumes can make you sick. Wear rubber gloves and mix the acid and water outdoors or in a fume hood.
Method:
Wet stained timber with cold water, then
Scrub affected area with a stiff bristled nylon brush (vigorously)
Leave 20 minutes then wash of with high pressure hose or something like a Karcher.
Repeat if necessary.
Leave timber to dry in open air.
Sand to a smooth finish.
I did this on a Tasmanian Oak table top in laid with Huon Pine and Myrtle. The mixture didn't affect any of the timbers or the glue holding it all together.
Hope this is useful.
PS. Got the Oxalic Acid (dry crystal form) at a 3D Paint Shop.If you never made a mistake, you never made anything!
-
23rd November 2005, 01:31 PM #7
Many, many years ago I was gluing some mahogony veneer and weighed it down with some scap steel pieces. Some glue seeped though a join in the veneer and rusted the steel, staining the mahogony. My father (a chemist) gave me some Oxalic Acid crystals which totally removed the stain. I sanded and laquered the project and it looked perfect.
Disaster, the stain returned!
The message being, leave the job sit for a few days before refininshing, in case the stain returns. I may need more than one go to remove the satin permanently amd if you seal it - you're stuck with it! I made my mistake about 35 years ago and I still have it to remind me. It annoys me every time I see it.
-
23rd November 2005, 06:44 PM #8
Water stain.
Hmmm. i'll keep an eye on it. Thanks for the warning.
Did you wsh it down with a neutralising agent. If not the stain may have been dead wood because the oxalic acid actually removes a layer of timber which you can see when you finish the scrubbing. I ran the Random Orbital Sander over it when it was dry before refinishing..
Cheers
PS: The new stain was probably iron oxide in the timber. (Rust)If you never made a mistake, you never made anything!
-
27th November 2005, 06:42 PM #9
Update on water stain
Here are the results of using Oxalic Acid (3 times) then 4 coats of China Wood Oil (2 days later) on the water stain. You can just see a little bit of stain at the top centre of the table top. Not a bad result really. I reckon I reduced the visual impact of the stain by 95%. The other closeup shots are just to show off my first attempt at inlaying other bits of timber. The small yellowish inserts are huon pine and the long narrow bits are myrtle. I made this hall table about 7 years ago and all I had was my Triton saw table and router. Originally sanded with a 1/4 sheet sander to 180 grit. This time sanded to 1200 grit.
Cheers
OOPs! forgot the pics. Herre they are.Last edited by watson; 2nd May 2010 at 05:21 PM.
Similar Threads
-
Stain Types
By Gazza in forum FINISHINGReplies: 2Last Post: 14th July 2005, 12:39 AM -
Gas hot water heaters
By Bob Willson in forum NOTHING AT ALL TO DO WITH RENOVATIONReplies: 28Last Post: 29th March 2005, 12:16 PM -
Water Crisis!!
By Tikki in forum NOTHING AT ALL TO DO WITH RENOVATIONReplies: 18Last Post: 19th November 2004, 03:51 PM -
Water Based Stain
By Mmcbain in forum FINISHINGReplies: 1Last Post: 8th June 2004, 02:35 PM -
Water stained window sills - How to repair and finish
By vk3em in forum FINISHINGReplies: 17Last Post: 12th July 2003, 10:04 AM
Bookmarks