Thanks: 0
Likes: 8
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
Thread: G'day from Northern NSW
-
7th September 2021, 02:19 PM #1
G'day from Northern NSW
Hi all. I'm Rob and I'm from Northern NSW. I joined the Forum last year but had nothing to say so didn't post. I still don't know if I have much to contribute, probably just asking obscure questions.
I'm a retired old fart who likes to "play" with my Nova Comet II Midi lathe, with "play" being the key word. I bought the lathe second hand and for what I do, it's ideal. The last time I used a lathe would have been maybe 1965.
So far I've managed a few small bowls as well as timber and resin "constructions". I don't know what is the harder to master the timber or the resin! But either way, it sure is enjoyable.
This Forum is immense. The amount of information stored within is immense. I've already had difficulty in later relocating information I had already found. My memory is not now immense.
And for now, that's me.
Cheers and regards
Rob (waltz)
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 , 0Scally liked this post
-
7th September 2021, 03:21 PM #2
G'Day & Welcome to a top forum "Rob" .....
There are quite a few members on the NSW North Coast with a stack members around Brisbane and cross South East Queensland plus the rest of the country.....
You'll find a heap of helpful & knowledgeable blokes & ladies on the forum and for most very willing to assist.
Make sure you show off your handiwork as everyone loves a photo, especially WIP [Work In Progress] photos with build notes.
Enjoy the forum.
Enjoy your woodwork......
Cheers crowie
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 , 0waltz liked this post
-
7th September 2021, 03:32 PM #3
Welcome to the forum Rob.
Ross
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 , 0waltz liked this post
-
7th September 2021, 07:44 PM #4
Welcome Rob
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 , 0waltz liked this post
-
7th September 2021, 09:07 PM #5
Welcome to the forum Rob. Lucky you, living in the land of Camphor Laurel.
Rgds,
Crocy.
-
Post Thanks / Like - 0 Thanks, 2 Likes, 0 , 0
-
7th September 2021, 09:39 PM #6
Welcome mate. I've just made the long journey north from Canberra to South of Coffs Harbour. Just finished coating all my machines with rust prevention spray and put them into storage until I can get A workshop again. I have an old woodfast lathe also and looking to do more turning
Certainly lots of timber up here, was given a few logs couple iron bark and couple tallowood. Loving the change of weather and pace.
Plenty of topics to be immersed in on the forum
Wealth of knowledge. Welcome
Cheers
Nathan
Sent from my Nokia 3.4 using Tapatalk
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 , 0waltz liked this post
-
10th September 2021, 07:39 AM #7
Welcome to the forum Rob
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 , 0waltz liked this post
-
12th September 2021, 10:34 PM #8
Welcome to the forum Rob.
Regards
Keith
Similar Threads
-
G'day from Far Northern NSW :) !
By JoshWoody in forum G'day mate - THE WELCOME WAGON -Introduce yourselfReplies: 9Last Post: 29th December 2020, 11:13 AM -
A BIG HELLO for Northern Vic
By Rowdy_Rod in forum G'day mate - THE WELCOME WAGON -Introduce yourselfReplies: 5Last Post: 31st May 2011, 12:54 AM
Bookmarks