Thanks: 4
Likes: 63
Needs Pictures: 0
Picture(s) thanks: 14
Results 16 to 30 of 38
Thread: Challenge 2020-2021 Labr@
-
28th May 2021, 03:40 PM #16
Managed to glue up the central pieces. It's a bit cool here at present so will leave it overnight to be sure.
IMG_20210528_133344 [800x600].jpg
Might have a go at making another float in the meantime.Cheers, Bob the labrat
Measure once and.... the phone rings!
-
28th May 2021, 09:58 PM #17
Labr,
Your making some serious progress, I think you may be the only true Laminated design plane.
I think [emoji6].
Keep up the good work.
Cheers Matt.
-
30th May 2021, 11:15 PM #18
Matt, I reckon the one by Bellbodyboards is laminated but I haven't noticed any others.
I spent the last couple of days gluing up the laminations on mine one at a time. There was slight bowing on some pieces and previous experience tells me that clamps can deal with this one layer at a time but not multiple.
So here is the glued up body that I can cut the final shape from. The pencil lines at top and right are at the required skew angle of 20 degrees.
P1110348 [800x600].JPG
I suspect that there will be a lot more fettling than previously expected because most of the joints have very slight misalignments.
Have had a few ideas about handles but will wait until the body shape has been rough cut before deciding.Cheers, Bob the labrat
Measure once and.... the phone rings!
-
31st May 2021, 08:53 PM #19
Lost some time (and money of course ) to an emergency vet visit today but still managed some progress.
Hot glued the assembly to a piece of thin ply so it had a straight edge to run along the bandsaw fence. Took a slice off each side and it turned out reasonably well. The cuts are pretty straight as shown by the steel rule and bench top.
P1110350 [800x600].JPG
There is just 1 significant ridge on each side where the blade went into air in the corners made by the staggering of the pieces.
P1110351 [800x600].jpgP1110358 [800x600].JPG
Also cut 1 end off square with a pull saw and that was it for today..
P1110355 [800x600].JPGCheers, Bob the labrat
Measure once and.... the phone rings!
-
31st May 2021, 10:19 PM #20
Labr.
This is looking very interesting can’t wait for more progress.
Cheers Matt.
-
1st June 2021, 10:02 AM #21GOLD MEMBER
- Join Date
- Oct 2018
- Location
- Dandenong Ranges
- Posts
- 1,845
Now I see what you're up to. Very clever creating the skew with the angled glue up!
-
1st June 2021, 08:40 PM #22
This is the most laminated plane I have seen. Except one where that guy made a plane out of plywood.
You might as well call this "The Laminator"
Hasta la vista, endgrain!
Sent from my SM-G781B using Tapatalk
-
4th June 2021, 01:00 AM #23
OK, so it's out with "Floatie" and in with "The Laminator" for a name.
Spent the last couple of days squaring things up, interior fettling and working on a handle idea. Still have a slight rock when the plane is placed on the shooting board - and unfortunately it's not the board's fault so there is still some work to do on that.
The aims of the handle design are to give a comfortable grip while allowing control in what I consider the important dimensions. That is forward/backward, rotation about the longitudinal axis and rotation about the vertical axis. This allows the plane to be held firmly against the workpiece while taking cuts. The only problem is that the handle looks rather curvy whereas the plane body is all straight surfaces so they seem to clash fairly seriously. Maybe I'll get used to it.
Originally intended to glue the handle on but am now leaning toward screws going into thread inserts.
IMG_20210603_221403 [800x600].jpg IMG_20210603_221503 [800x600].jpg
Also been thinking about adding a metal button on the rear end for the knockometer to strike when backing off the blade. Does anyone know how thick these normally were and how they were attached?Cheers, Bob the labrat
Measure once and.... the phone rings!
-
4th June 2021, 07:54 AM #24
The name is whatever you want to give. But it seems there is a consensus that the planes should have a nickname. Anyway up to you.
The plane looks really good. I like the handle. If you think it clashes with the boxy shape of the plane body I can see that there is enough room to also add some curves to the body without interfering with it's function.
I have seen people using the head of carriage bolts for the strike button.
Sent from my SM-G781B using Tapatalk
-
4th June 2021, 02:07 PM #25
-
4th June 2021, 02:33 PM #26
-
4th June 2021, 03:50 PM #27
-
5th June 2021, 02:36 PM #28
Took a few swipes on the shooting board without the handle and found that although it did take some form of shaving they were not so good and it also seemed to clog. So I did some more fettling inside including tapering the front of the abutments to give clearance for the shavings to exit. It still needs some smoothing/cleaning up but the functionality is better.
P1110365 [800x600].JPG
Also attached the handle and did final shaping of the wedge. The handle is quite comfortable and makes the plane controllable.
P1110362 [800x600].JPG IMG_20210605_105055 [800x600].jpg
Tried it on some blackwood end grain:
IMG_20210605_105015 [800x600].jpg
And Oregon side grain:
P1110369 [800x600].JPG P1110374 [800x600].JPG
So it works better than any other plane I've tried on the shooting board but it could still be better. More attention to sharpening could be part of the equation and I reckon the shooting board could be better too.
The ends of the body are still to be finished, corners to be softened and there is some tearout on the top that may just have to remain - I don't want to remove that much material now.Cheers, Bob the labrat
Measure once and.... the phone rings!
-
5th June 2021, 04:53 PM #29SENIOR MEMBER
- Join Date
- Sep 2010
- Location
- Port Sorell, Tasmania
- Posts
- 329
You can't use up creativity. The more you use, the more you have. ~Oscar Wilde
-
5th June 2021, 06:06 PM #30
Interesting you say that Tony - in the process of squaring up the throat on mine I would have opened it up a bit so that may well have been a contributing factor.
Cheers, Bob the labrat
Measure once and.... the phone rings!