![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 10 of 10
Thread: Another spinning wheel repair
-
12th June 2019, 11:15 PM #1
GOLD MEMBER
- Join Date
- Oct 2002
- Location
- NSW
- Posts
- 0
Another spinning wheel repair
I have spotted a couple of problems with this wheel...
IMG_20190607_140530.jpg
IMG_20190607_140448.jpg
IMG_20190607_140459.jpg
Step 1 was to chase down the cardboard box which had been 'protecting' it, and collect the splinters and chips of wood.
I've been able to put the jigsaw back together, but I'm not sure whether just glueing will be sufficient, or whether I need to be considering doing some reinforcement as well.
I'd also appreciate if anyone has suggestions about the make, style etc. as I've just started this, and it's my first spinning wheel.
One feature I haven't seen on any other wheels is the tension adjustment, which is the decorative top of one of the maidens, when turned raises and lowers one end of the shaft for the flyer and bobbin.
IMG_20190611_204815.jpg
-
12th June 2019, 11:26 PM #2
Ouch not good at all. You are right just gluing the jigsaw together will only result in it breaking again.
I'd suggest making a whole new leg for starters.
If possible to remove the whole broken bits from the table glue it all together then bore down through the centre and place either a dowel or steel rod gluing it into it for added strength.
Good luck
-
14th June 2019, 08:15 AM #3
GOLD MEMBER
- Join Date
- Oct 2002
- Location
- NSW
- Posts
- 0
Unfortunately, it's not just one leg, it's two legs and both uprights that have been snapped off.
The holes for the uprights go right through the table
IMG_20190613_135519.jpg
IMG_20190613_135502.jpg
so I'll try to knock those bits out, or glue the uprights pieces together and drill & reinforce as suggested.
The owner has given permission to "add character" by drilling into the top of the table if that's the only way to reinforce the broken legs.
Anyway, baby steps so far are a 3-piece chip fix:
IMG_20190612_171737.jpg
IMG_20190613_133625.jpg
IMG_20190613_133943.jpg
and starting to piece together the snapped off leg:
IMG_20190613_134103.jpg
IMG_20190613_134836.jpg
-
16th June 2019, 06:45 AM #4
GOLD MEMBER
- Join Date
- Oct 2002
- Location
- NSW
- Posts
- 0
The jigsaw continues...
IMG_20190615_154902.jpg
IMG_20190615_154924.jpg
To get these pieces together, I had to tilt, twist, and wiggle, and the first attempt took ages. When glueing, I'll need to be able to get them together reasonably quickly and easily, so I have been repeating a cycle of fitting, wiggling, disassemble, trim off any bent or broken fibres, repeat...
IMG_20190615_155354.jpg
IMG_20190615_155447.jpg
The pieces go together easily enough now, so I'm working out how to clamp them when glued.
-
16th June 2019, 12:55 PM #5
Do you have any history on how it was damaged?
Also, is it a Castle style wheel? From the pix it's hard to tell... But some of the turning details, the shape of the table and that tension adjustment are typical of Rappard's "Wee Peggy."
Although the build quality doesn't look to be there. It may be a knock-off of the design. (Also, Ashford bought the rights to the design and are now producing it with 6 spoked wheels instead of Rappards 8 spokes.)
O' course, I could be way off base. A pic or two if the whole wheel would be very helpful...
-
16th June 2019, 04:46 PM #6
GOLD MEMBER
- Join Date
- Oct 2002
- Location
- NSW
- Posts
- 0
All I know is it was purchased in NZ, packed for transport to Australia, and was unpacked in pieces. The owner had been to the Ashford factory prior to buying the wheel privately.
The first thing I noted was the construction of the wheel segments - the joints are not radial, but match the diagram on this page about Rappard wheels:
RAPPARD WHEELS
The finish is poorly applied (suggesting a kit?) and there is evidence of previous repairs.
The leg which snapped off, failed through a large knot. Would this have passed factory quality control, or does it point to a knock-off.
The turnings are close, but not identical (like stuff from my lathe )
I haven't found any numbers on any parts yet, so am thinking a copy of a "Wee Peggy" as my uninformed best guess so far.
IMG_20190616_152511.jpg
IMG_20190616_153031.jpg
IMG_20190616_152520.jpg
-
16th June 2019, 04:54 PM #7
GOLD MEMBER
- Join Date
- Oct 2002
- Location
- NSW
- Posts
- 0
The wheel is made of 3 layers:
IMG_20190616_154942.jpg
IMG_20190616_154921.jpg
-
3rd August 2019, 07:04 PM #8
GOLD MEMBER
- Join Date
- Oct 2002
- Location
- NSW
- Posts
- 0
Slow, interrupted progress...
first leg is repaired.
IMG_20190803_180025.jpg
IMG_20190803_180010.jpg
-
3rd August 2019, 11:32 PM #9
A Wee Peggy is an upright wheel RAPPARD PEGGY SPINNING WHEELS
Looking at the 1971 model same sort of wheel assembly joint.
-
4th August 2019, 03:28 PM #10
There's a good trick for repairing broken spindles like that where a dowel can be added. You may get a use for it on some of the others.
IMG_1921.JPG
You drill 1 and then cut 2 through the first dowel hole . Drawing 1
Glue the break back on 3 and the first hole guides the drill back through the break . Drawing 2
Add a dowel and glue it up
That's how you get a dowel into such a thing .
In a turned chair leg like drawing 4 cut 2 goes through one of the turning points for an invisible fix .
The straight turned spindle on yours though could be done on the angle = stronger. Cut 2 in drawing 1 .
Rob
Similar Threads
-
WIP - Spinning Wheel Repair
By Skew's_Girl in forum RESTORATIONReplies: 15Last Post: 17th September 2016, 09:46 PM -
Hello, I'm new and looking for help restoring a spinning wheel
By spinderella in forum G'day mate - THE WELCOME WAGON -Introduce yourselfReplies: 6Last Post: 16th October 2009, 09:22 PM -
Spinning Wheel Restoration
By YAKI in forum FINISHINGReplies: 3Last Post: 25th January 2009, 07:31 AM