![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 4 of 4
-
1st August 2019, 11:47 PM #1
New power point fed from AirCon Isolator Switch?
Hi all,
I've just moved into a sweet little 2Br unit.
Need some wisdom, from those wise in these matters! I thought to ask the forum before I go to the expense of talking with a sparky.
The balcony outside has no power pointbut it does have a monster aircon.
Can I get (as in, Is It Allowed under Ze Rules) to put a power point (an outdoors style water proof) fed from this isolation switch?
The power board says the AirCon has an RCBO 20A going to it.
Clearly the juice for the new point/s would be fed from the input side of things.... or is it best, if one can, to run it after the isolator switch?
I am in Canberra ACT if it is of any consequence.
It is simply so I can plug in my small electric hibachi, run the scrollsaw and put up my xmas lightsblink blink!
TIA dudes!
IMG_20190801_202835.jpg IMG_20190801_202845 (1).jpg
-
2nd August 2019, 08:19 AM #2
GOLD MEMBER
- Join Date
- Mar 2018
- Location
- Sydney
- Posts
- 268
unlikely. I am not familiar with rules and regs, but this would be a specific purpose connection (the AirCon) on the fuseboard, and a GPO would need to be on a GPO circuit. Is there a GPO on the inside wall along the balcony? Often that's the simplest answer, punch thru from the inside where the power exists.....
-
2nd August 2019, 10:38 AM #3
.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 1,174
My understanding of the regs is large draw devices like large AC units must be on their own breaker with nothing else attached.
When our last installed AC unit was hooked up to one of the existing 10A house circuits I queried this with the supplier of the AC and he agreed and said that the sparky he had sent around to do the install had done this once too often and was the last time he would use him. Another sparky came around within 24 hours and installed another breaker just for that AC.
In terms of electrical safety, if a cross over switch was fitted (either the AC or the other power point was ACTIVE) there should be no safety issues, whether that meets code is another issue.
-
2nd August 2019, 06:41 PM #4
SENIOR MEMBER
- Join Date
- Apr 2016
- Location
- Mooroopna, Victoria, Australia
- Age
- 34
- Posts
- 33
Definite no go. High power items need to be on their own circuit. As mentioned above, if there's an internal powerpoint on the same wall, that can probably used to provide power.
Similar Threads
-
what is the horse power rating of my aircon??
By Reno RSS Feed in forum HEATING & COOLINGReplies: 0Last Post: 2nd November 2009, 12:30 AM -
How much power does the fan only setting of a small window aircon use?
By qld in forum NOTHING AT ALL TO DO WITH RENOVATIONReplies: 1Last Post: 2nd July 2009, 07:26 PM -
power point safety what is the recommended number of power points in a average house
By Reno RSS Feed in forum PLUMBING, ELECTRICAL, HEATING, COOLING, etcReplies: 0Last Post: 26th May 2009, 01:30 AM -
Light Switch and Power Point Plates
By seth in forum PLUMBING, ELECTRICAL, HEATING, COOLING, etcReplies: 13Last Post: 2nd January 2007, 09:13 PM -
Use of power point ok?
By Manda in forum PLUMBING, ELECTRICAL, HEATING, COOLING, etcReplies: 12Last Post: 5th September 2006, 04:52 PM