Results 1 to 10 of 10

Thread: Finishing Table

  1. #1
    Join Date
    Aug 2011
    Location
    Brookfield, Brisbane
    Age
    50
    Posts
    0

    Default Finishing Table

    Hi WWF,

    i just oust finished building, staining and clear coating our new trestle table for our deck.

    image.jpg
    As the table was so large it took me about 20 mins to paint the top. As a result you can see brush marks between the sections I started on and the sections I finished. There is 2 coats of clear top on.

    i was wondering if anyone knew of a way I could remove the brush marks?

  2. #2
    Join Date
    Nov 2012
    Location
    Brisbane
    Posts
    596

    Default No magic bullet that I know of

    The only way that I know is to wait until it is set very hard then sand it smooth, preferably without going right through the existing coats, then re-coat with a very fine wide brush. If you sand before the finish is very hard you will get a nasty mess as the sanding pulls lumps out of the thicker sections of varnish.

    If you can get a helper you could start from each end and finish in the middle. Then "dry brush" over the whole surface before it sets to ensure it is quite smooth all over. If no helper is available you have to keep a "wet edge" at all times and move very quickly. Since the temperatures are lower now you should have longer working time for the finish.

    Now, if you had used shellac you could just refresh your rubber and work over the surface until it was perfect!

    Hope this helps

    David

  3. #3
    Join Date
    Sep 2013
    Location
    Cherrybrook,NSW
    Posts
    36

    Default

    You could try using a deck oiling mop to apply the finish if you choose to sand it back.

  4. #4
    Join Date
    Aug 2011
    Location
    Brookfield, Brisbane
    Age
    50
    Posts
    0

    Default

    Quote Originally Posted by Xanthorrhoeas View Post
    The only way that I know is to wait until it is set very hard then sand it smooth, preferably without going right through the existing coats, then re-coat with a very fine wide brush.

    David
    Thanks for the input David.

    by smooth do you mean light sand with a 240 grit or something else?

  5. #5
    Join Date
    Aug 2011
    Location
    Brookfield, Brisbane
    Age
    50
    Posts
    0

    Default

    Quote Originally Posted by Wood Collector View Post
    You could try using a deck oiling mop to apply the finish if you choose to sand it back.

    Thanks WC however it is not enough of a concern for me to go down this path

  6. #6
    Join Date
    May 2003
    Location
    Central Coast, NSW
    Posts
    614

    Default

    You haven't indicated what the 'clear' you finished it with was, so its a bit hard to comment.

    If its what most people call a 'varnish' (generally polyurethane resin in either a water or oil base) then faults are hard to repair. That's because the multiple coats do not meld with each other, and if you sand through one coat into another then you will get a watermark where you have cut through the top coat.

    As the other posters have indicated, you can try sanding the affected area. OK if you don't cut through the top coat. Try anything from 400 to 1200 grit, 240 will cut too quickly.

    Personally, if the table was important to me, I'd just sand it all off back to bare timber and start again. Often much quicker in the long run.

    Anyway, it sounds like your problem is lap marks, not brush marks. To avoid both in future, use a bit of Penetrol in the varnish. It will stop the edge drying, flatten out brush marks, and slow the whole thing down so you can concentrate on quality of job, not racing the product.

    cheers
    Arron

  7. #7
    Join Date
    Aug 2011
    Location
    Brookfield, Brisbane
    Age
    50
    Posts
    0

    Default

    Quote Originally Posted by Arron View Post
    You haven't indicated what the 'clear' you finished it with was, so its a bit hard to comment.

    If its what most people call a 'varnish' (generally polyurethane resin in either a water or oil base) then faults are hard to repair. That's because the multiple coats do not meld with each other, and if you sand through one coat into another then you will get a watermark where you have cut through the top coat.

    As the other posters have indicated, you can try sanding the affected area. OK if you don't cut through the top coat. Try anything from 400 to 1200 grit, 240 will cut too quickly.

    Personally, if the table was important to me, I'd just sand it all off back to bare timber and start again. Often much quicker in the long run.

    Anyway, it sounds like your problem is lap marks, not brush marks. To avoid both in future, use a bit of Penetrol in the varnish. It will stop the edge drying, flatten out brush marks, and slow the whole thing down so you can concentrate on quality of job, not racing the product.

    cheers
    Arron

    Thanks Arron,

    i think ink you are right about the lap marks. The clear I used is a Urethane - see pic.

    i thought about using some 400 on my ROS however I have not been able to find anything finer then 240.

    if I just work on the affected areas and apply the clear again will that not just exacerbate the problem?
    Attached Images Attached Images

  8. #8
    Join Date
    May 2003
    Location
    Central Coast, NSW
    Posts
    614

    Default

    Quote Originally Posted by Damienol View Post
    if I just work on the affected areas and apply the clear again will that not just exacerbate the problem?
    Possibly, as I said fixing poly and urethane varnishes is difficult. They are not made for that.

    What I would do is allow a couple of weeks for it to fully harden, then with 400 grit rub over the affected area removing any unevenness to the hand but being careful not to cut through the top coat. If you do, you will get one of those squigly watermarks, which will be diminished when you put the next coat on but never fully disappear. Then I'd recoat the whole top, but putting some Penetrol in the mix (after checking its compatible, of course) so you dont get brush or lap marks.

    I always use 400 as my grit between coats and have never had a problem. I use 1200 after the job is finished and I just want to buff up without tearing at the surface.

    That would be my second best option. Best option I've already mentioned - that table looks too finer job to not be worth sanding the top back to bare and doing again.

    Cheers
    Arron

  9. #9
    Join Date
    May 2003
    Location
    Central Coast, NSW
    Posts
    614

    Default

    Oops. Just reread my post and realised I said penetrol when I meant flowtrol ( floetrol ??). Anyway, the maker of both products is Flood and they are pretty helpful.
    Cheers
    Arron

  10. #10
    Join Date
    May 1999
    Location
    Grovedale (Geelong) Victoria
    Age
    75
    Posts
    9,665

    Default

    As Arron said.

    Also... Make sure you have a really good brush that's designed to work with the finish you are using and not a $5 one from Bunnies or K Mart, etc. Go to a proper paint shop and ask for their help in getting the right brush for the product and the job. Just because a brush is wide doesn't mean it is the right one for the job at hand. Most are made for paint not for varnish or clear finishes.

    If the sales person in the shop hesitates or scratches their head, walk away and try another. There are plenty of them and with luck you'll find one staffed by people who know what they're talking about.

    Oh yeah, and next time buy good quality Australian product..... Sarcasm, sorry.

    Cheers - Neil
    KEEP A LID ON THE GARBAGE... Report spam, scams, and inappropriate posts, PMs and Blogs.
    Use the Report icon at the bottom of all Posts, PM's and Blog entries.


Similar Threads

  1. Finishing a table
    By Johncs in forum FINISHING
    Replies: 3
    Last Post: 3rd May 2009, 10:31 PM
  2. Finishing a table top
    By kcoj in forum FINISHING
    Replies: 0
    Last Post: 8th March 2009, 04:11 PM
  3. Finishing of Jarrah Table
    By shapes in forum FINISHING
    Replies: 2
    Last Post: 31st July 2008, 03:25 PM
  4. finishing red gum table top
    By back yarder in forum FINISHING
    Replies: 13
    Last Post: 13th September 2007, 05:56 PM
  5. Finishing of table top
    By new woodworker in forum FINISHING
    Replies: 8
    Last Post: 27th November 2006, 07:26 PM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •