![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 7 of 7
Thread: Quality of modern white goods
-
9th August 2014, 02:42 PM #1
.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 1,174
Quality of modern white goods
I've taken apart more than my fair share of white goods as I use the wiring in my electrical/electronic projects and the parts for a wide range of "projects". All of the "goods" I have taken apart so far have been in the 15+year old range and they usually use proper microswitches, solid spade type connectors, and screw type hose clamps etc, that continue to make them useful. The only newish machines I have looked inside recently are our Asko dishwasher and washing machine and they also look reasonable although I the hose clamps are single use only.
A couple of days ago I was given a front loading Whirlpool washing machine with a dead motherboard that was just 6 months outside it's 12 month warranty.
As the cost of repair was around 1/3rd of the cost of a new machine the owner went and purchased a new machine.
This morning I took it apart and although I was expecting it to be poorly made I have to say I was still surprised at just how poor they have become.
Cosmetically the machine looked brand new as the previous owners only used it sparingly, i.e. significantly less than a family would use it.
However, the small amount of metal used inside the machine had already started to rust.
Come to think of it, apart from 3 sides of the cabinet, the inside tub, a few nuts and bolts, the conductors and the motor there was no other metal in it! Just plastic and the concrete damping lumps.
Some of the ( plastic) hose connectors were so brittle they snapped at the slightest tug.
Some of the proprietary electrical connectors/plugs also were also fragile and these (not that I usually use them) also fell apart.
The good thing about all this was that I got the whole electrical harness out in about 3 minutes
The plastic tub dampers came out with a simple wrist twist
The door switch so poorly made it was not worth keeping.
All in all if the motherboard had been replaced the machine was not likely to only have lasted much longer before something else would go wrong
So what did I get out of it
- a plastic pressure switch that could be useful
- A 12A 240V EMI "white plastic sealed" EMI filter that I have some ideas for
- 3 fluid solenoids - at least these have accessible spade connectors
- a 30W plastic water pump (useful as coolant pump) with proprietary connectors embedded inside a plastic block that will be difficult to attach to.
- the motor is a 12,000 rpm 1/3rd HP brushed motor so it has limited application. It has many more wires on it than usual, some of which are related to speed control. It uses the typical 5v-ribbed belt with a 20:1 drive/drive pulley ratio.
- $4.50 in coins inside the tub.
I'm still happy with what I managed to recover as my work rate is usually only about $5/hour anyway so I guess the change in the tub made it worthwhile
I'm not expecting manufacturers to make machines I can scavenge stuff out of but I have never seen a white goods machine clearly designed to last just past it's warranty period.
-
9th August 2014, 03:02 PM #2
.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 1,174
The plastic top of the washing machine was about 12mm thick and I though it might make a useful piece of thick plastic to do something with so I started to cut the round edges off and guess what - its not solid plastic, its a 1 mm thin skin of plastic covering 10 mm thick chipboard.
I guess that sums up the whole appliance.
-
9th August 2014, 03:24 PM #3
Crikey, that sounds like a POS. I purchased a F & P in 1997 and it gave me 17 years of yeoman service. Couple of minor repairs along the way.
Finally threw the towel in (?) a few months ago so we replaced it with another F & P. Strangely enough they are still made in NZ but who knows where the parts come from.
Glad you at least got paid for this job!
-
13th August 2014, 09:19 PM #4
Your friend should have had it repaired under "Implied Warranty". Under consumer laws an item has to last a reasonable amount of time, even if they only state a 12 month warranty, 18 months for a washing machine is not reasonable. Most retailers will not tell you about it & you may have to go to your state fair trading dep't to get help, but it is worthwhile.
-
13th August 2014, 09:58 PM #5
.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 1,174
I agree it's not reasonable but I advised the owner against getting it repaired been if it could have been done free as it would be just a matter of time before something else went wrong.
Anyway. It's a bit late now, what's left of the machine is in the white goods waste collection dumpster at our local waste transfer station.
-
13th August 2014, 11:02 PM #6
Bob these products are engineered to last a life time...........who or whats I am not sure. One electrical surge can fry any white good products mother board even on day one of ownership.
-
13th August 2014, 11:14 PM #7
GOLD MEMBER
- Join Date
- Dec 2010
- Location
- Mornington Peninsula
- Posts
- 408
Similar Threads
-
Payment for goods
By gmoss in forum FORUMS INFO, HELP, DISCUSSION & FEEDBACKReplies: 5Last Post: 7th November 2012, 01:37 PM -
Southern Star - White Wheel Or White Elephant?
By Metal Head in forum NOTHING AT ALL TO DO WITH RENOVATIONReplies: 2Last Post: 4th February 2009, 01:51 PM -
Goodes the goods again?
By bennylaird in forum NOTHING AT ALL TO DO WITH RENOVATIONReplies: 27Last Post: 27th September 2006, 07:24 PM