Thanks: 0
Likes: 1
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 10 of 10
-
4th January 2014, 10:55 AM #1
How would you make this to account for wood movement?
How would you make a table top like this and allow for the natural movement of the woods? I love the look and would like to try something similar but can't see how it would be a long term option. Here's a link to the original
It's only a mistake if you don't learn from it.
-
4th January 2014, 11:14 AM #2
I would be doing the parquetry 4 to 5 mm thick and gluing that down onto some good quality plywood with a two pack glue. Then surround the edge with a frame , mitered or plain .
The frame , in four pieces on the bench could be built up brickwork style with different timbers with the grain going in the same direction though.
use a biscuit joiner to fit it on , if you have one.
Rob
-
4th January 2014, 11:20 AM #3
Hi Corbs,
According to the link, it is glued up in three layers so its a bit like plywood.
Plus, the pieces are all small so the movement in each individual piece would be relatively small.
I reckon you would need to put a fair bit of thought into the layering and obviously put the better looking pieces on the outside and use a strong glue.
You might even consider making the core layer out of plywood and edge and cover it with the other pieces.
Someone with more experience than me may have other ideas but that's my 2c
Cheers
DougI got sick of sitting around doing nothing - so I took up meditation.
-
4th January 2014, 04:52 PM #4
The cracks will show sooner or later whether you like it or not. It is a poor job as there are lots of gaps between the pieces.
Visit my website at www.myFineWoodWork.com
-
4th January 2014, 07:39 PM #5
Thanks for the replies team... Wongo, I was of the same impression. Unless the top is made from thin veneers I can't see how this wouldn't open up with cracks everywhere.
I showed SWMBO and it was not approved so I guess how it's put together isn't really importantIt's only a mistake if you don't learn from it.
-
4th January 2014, 11:26 PM #6
How much do they want for it??????? "Skilled craftsmanship" ??????? That shot of the surface looks like there's enough gap between some of the timbers to stuff a few matchsticks in! Sorry, for that much money I'd want a properly jointed top!
-
4th January 2014, 11:56 PM #7
-
5th January 2014, 01:07 AM #8
I'm assuming that it is some sort of filler; but it's filler to fill holes where it seems that lengths have been incorrectly cut or where a 90 degree angle isn't 90 degrees (it's not like there's a 'oh, it's a hand cut dovetail' type of excuse).
-
5th January 2014, 12:24 PM #9
The pieces are just not square. It is as simple as that. Skilled craftsmanship? What Skilled craftsmanship? Let's just call it rustic.
Visit my website at www.myFineWoodWork.com
-
5th January 2014, 02:13 PM #10
To stop movement it could be glued and encapsulated with epoxy glue (marine grade would be the ticket), and then varnished with an exterior grade or (better) marine grade varnish. e.g. as per boat building. I have a small boat that was built in this manner 20 -30 years ago, and the joints are still crisp. The trick is to encapsulate with epoxy glue, and then to keep up with the varnish before it breaks down due to UV, or due to damage.
That said... a table like that is not to my liking... it would make my eyes itchy.