Results 1 to 7 of 7

Thread: Jafo :)

  1. 26th November 2013, 08:57 PM #1
    MickR
    MickR is offline New Member
    Join Date
    Nov 2013
    Location
    Brisbane/Redcliffe
    Posts
    3

    Default Jafo :)

    G'day all, My name's Mick. I'm reasonably new to all this turning stuff and to date haven't done much more than a shaving brush in a bit of off cut timber just to see if I could, and a few fipple blocks for whistles made out of electrical conduit. The blocks were turned down to size from a length of Delrin rod. So as you see I don't have a great deal of experience, and now I find myself in woes with my old lathe, which is the reason why I came here in the first place. I need help sourcing a part for my lathe. Where should I post these sort of questions? Thanks for any help you can provide.


    Mick
    Reply With Quote Reply With Quote
  2. 26th November 2013, 09:37 PM #2
    old1955
    old1955 is offline GOLD MEMBER
    Join Date
    May 2013
    Location
    Rockhampton QLD
    Age
    69
    Posts
    1,570

    Default

    Welcome to the forum Mick.
    Reply With Quote Reply With Quote
  3. 26th November 2013, 10:16 PM #3
    tdrumnut's Avatar
    tdrumnut
    tdrumnut is offline Keeper of the wood
    Join Date
    Jan 2011
    Location
    Ormeau, Gold Coast, Australia
    Posts
    203

    Default

    Gidday & welcome aboard Mick, may your journey with us be a pleasant one.
    Regards Rumnut.

    SimplyWoodwork
    Qld. Australia.
    Reply With Quote Reply With Quote
  4. 28th November 2013, 08:27 AM #4
    MickR
    MickR is offline New Member
    Join Date
    Nov 2013
    Location
    Brisbane/Redcliffe
    Posts
    3

    Default

    Thanks for the welcome Gents. I've been looking around for a section here to post up my lathe problem, to seek out help, but I'm not sure where I should post it. So I think the small machinery section might be the best area. I'll try there anyway. Thanks again for the welcome.


    Mick
    Reply With Quote Reply With Quote
  5. 28th November 2013, 08:37 AM #5
    JJF's Avatar
    JJF
    JJF is offline GOLD MEMBER
    Join Date
    May 2011
    Location
    FRANCE
    Age
    59
    Posts
    1,889

    Default

    Welcome to the forum
    Reply With Quote Reply With Quote
  6. 28th November 2013, 09:20 AM #6
    crowie's Avatar
    crowie
    crowie is offline Life's Good, Enjoy each new day & try to encourage
    Join Date
    Dec 2009
    Location
    Faulconbridge, Lower Blue Mountains
    Age
    68
    Posts
    2,576

    Default

    G'Day & Welcome to a top forum "Mick".
    There are quite a few members in and around Brisbane & SE Queensland.....
    You'll find a heap of helpful & knowledgeable blokes & ladies on the forum and for most very willing to assist.
    Make sure you show off your handiwork as everyone loves a photo, especially WIP [Work In Progress] photos with build notes.
    Enjoy the forum.
    Enjoy your woodwork..
    Cheers crowie

    PS - It's best to ask the specific question in a number of sub-section to great a wider audience...
    GENERAL & SMALL MACHINERY
    WOODWORK - GENERAL
    HAND TOOLS - POWERED
    WOODWORK - GENERAL
    WOODTURNING - GENERAL
    Reply With Quote Reply With Quote
  7. 28th November 2013, 03:08 PM #7
    MickR
    MickR is offline New Member
    Join Date
    Nov 2013
    Location
    Brisbane/Redcliffe
    Posts
    3

    Default

    Quote Originally Posted by crowie View Post
    G'Day & Welcome to a top forum "Mick".
    There are quite a few members in and around Brisbane & SE Queensland.....
    You'll find a heap of helpful & knowledgeable blokes & ladies on the forum and for most very willing to assist.
    Make sure you show off your handiwork as everyone loves a photo, especially WIP [Work In Progress] photos with build notes.
    Enjoy the forum.
    Enjoy your woodwork..
    Cheers crowie

    PS - It's best to ask the specific question in a number of sub-section to great a wider audience...
    GENERAL & SMALL MACHINERY
    WOODWORK - GENERAL
    HAND TOOLS - POWERED
    WOODWORK - GENERAL
    WOODTURNING - GENERAL

    Thanks mate. Seems that it doesn't want me to make the post I need to make with photo's. I'm having no end of technical glitches with he forum. Probably user error, but a pain in the behind none the less.
    What I need to find out is where to get a replacement rear bearing for Remag WL 800. Any ideas?


    Mick
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules