Thanks: 0
Likes: 1
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
Thread: Ironbark Logs
-
24th September 2013, 10:33 AM #1
Ironbark Logs
Howdy,
I have some small iron bark logs I got from my property 300-400 dia, 700-800 long. I have sealed the ends with Caltex timber sealer and wanted to find out how the timber would go if I cross cut the logs into 40-50mm plates then sealed and strapped them for drying. Would they cup or split? or should I try to dry them a bit via a solar kiln before cutting?
Any advice is appreciated as always
Cheers
Damian
-
24th September 2013, 12:52 PM #2.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 24,746
They are likely to spilt even if they are sealed and strapped and there is very little you can do about it.
Some techniques used to reduce the splitting are;
- dig a 1m hole and line it with a 250 mm layer of wet sawdust, pack in the rounds up to 250 mm and cover with a 250 mm layer of wet sawdust cover with a 250 mm layer of soil . Saturate the whole thing with water and keep it damp for a year - dig them up and let them dry slowly out of direct sunlight and medium light ventilation.
- put then underwater for a year and then do the same as above.
Some will still spit but hopefully not as many as otherwise might. You might also get some interesting fungal patterns with the first method.
-
24th September 2013, 05:00 PM #3
I would be inclined to mill all the back-sawn/rift-sawn boards oversize,this way it will ensure that you are left with the desired thickness,after dressing them.Being small logs,good chance that some boards WILL move during seasoning..do the logs have much sap? If so,get stuck into 'em before the borers do...good luck with 'em...MM
Mapleman
-
24th September 2013, 06:08 PM #4.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 24,746
-
24th September 2013, 06:11 PM #5
-
24th September 2013, 10:01 PM #6
Thanks for the advice lads.
I've attached a few pics of them. I was hoping to make lazy Susan's/serving boards out of them. I have heard ironbark is notorious for checking so I don't think i'll have much luck with them. I might experiment with a few and see how they go.
Red Ironbark? Talk about heavy, it took two of us to lift them!
Ironbark02.jpgIronbark03.jpgIronbark04.jpgIronbark01.jpg
-
24th September 2013, 11:42 PM #7
I tend to agree with Bob. You could try slicing a few at 25mm thick, then store them in a large container with 50/50 detergent (cheap stuff will do) and water for around a year, way down the back yard (it will not look or smell pretty ). Then bury the blanks in sawdust in a hessian bag, down the back again out of the sun, and hope the termites don't get it.
Neil____________________________________________Every day presents an opportunity to learn something new
-
25th September 2013, 06:22 PM #8
Ok cheers, thanks for the advice
-
1st October 2013, 07:29 PM #9Senior Member
- Join Date
- Sep 2012
- Location
- NSW, Australia
- Posts
- 29
Bit late to the party, but there's a trick you can try for small sections, if you're so inclined. It would be a bit much to try doing it for large volumes, but this used to be done for wooden plane bodies and similar things.
Basically, you replace the water with something else. This can be paraffin or whatever is suitable. Method is to immerse the lump of green wood in your whatever, and have that inside a container of water. Heat the water to boiling point. Heat will transfer to parafffin/whatever, and then to the water inside the wood, which will slowly boil out and be replaced by the paraffin.
Result should be a perfectly stable piece of wood, without incurring any checking or other distortion.
Just threw my 2c in because I saw "ironbark", which has long been one of my favourites (even if it is a bit of a mongrel to work).
Similar Threads
-
Raw Ironbark
By jkd87 in forum FINISHINGReplies: 0Last Post: 29th December 2010, 04:28 PM