![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 6 of 6
Thread: Hare and Forbes TS12
-
13th July 2013, 05:48 PM #1
Senior Member
- Join Date
- Feb 2012
- Location
- Sydney
- Posts
- 120
Hare and Forbes TS12
Hey all,
I recently received a a! Table saw. Its a hare and forbes TS12 contractors saw. I Have a few questions regarding the saw , and wondering if anyone has some answers.
1. Its a 12 blade with a 16mm arbor is that standard?
2. Is it worth trying to pull the arbor and replace the bearings? they are not as good as they should be
3.Are link belts really worth it?
4. Any aditional info on the saw?
Check me out:
www.facebook.com/steamjunkprops Or Steamjunkprops.deviantart.com
-
13th July 2013, 06:06 PM #2
[QUOTE=steamjunkprops;1672302]Hey all,
I recently received a a! Table saw. Its a hare and forbes TS12 contractors saw. I Have a few questions regarding the saw , and wondering if anyone has some answers.
1. Its a 12 blade with a 16mm arbor is that standard?It might be a 10", but with a 12" blade.
2. Is it worth trying to pull the arbor and replace the bearings? they are not as good as they should be Not fun but doable. Helps if you have a mate with half an idea and a hydraulic press to get the bearings onto the arbor
3.Are link belts really worth it? Yes, improved my contractor saw's power output noticeably. The pain in the wallet has been forgotten over the past 8 or so years, to the extent that whatever machine's I could, I changed - Drill Press, Thicknesser and Jointer. More power, smoother transmission of power, easier to maintain.
4. Any aditional info on the saw? Grizzly has the best range of manuals, this one might even be close enough for you to decide on it's usefulness to you.Pat
Work is a necessary evil to be avoided. Mark Twain
-
13th July 2013, 06:11 PM #3
Senior Member
- Join Date
- Feb 2012
- Location
- Sydney
- Posts
- 120
Thanks for the extra info
The saw says it is a 12inch contractors saw
Check me out:
www.facebook.com/steamjunkprops Or Steamjunkprops.deviantart.com
-
14th July 2013, 04:29 PM #4
Senior Member
- Join Date
- Feb 2012
- Location
- Sydney
- Posts
- 120
I just pulled the arbor from the saw, easier than expected, next step is going to cbc bearings to get bearings bulled and pressed
Check me out:
www.facebook.com/steamjunkprops Or Steamjunkprops.deviantart.com
-
14th July 2013, 05:18 PM #5
Senior Member
- Join Date
- Feb 2012
- Location
- Sydney
- Posts
- 120
I just pulled the arbor from the saw, easier than expected, next step is going to cbc bearings to get bearings bulled and pressed
Check me out:
www.facebook.com/steamjunkprops Or Steamjunkprops.deviantart.com
-
2nd August 2013, 09:38 PM #6
Senior Member
- Join Date
- Feb 2012
- Location
- Sydney
- Posts
- 120
Ive completed swapping out my bearings without any special tools
Check me out:
www.facebook.com/steamjunkprops Or Steamjunkprops.deviantart.com