Results 1 to 7 of 7
  1. #1
    Join Date
    Jan 2002
    Location
    Sunshine Coast, Qld
    Posts
    117

    Default Tung oil not drying on silky oak

    Wondering if anyone has had the same experience. I finish most furniture with pure tung oil with no problems (3 to five coats with 2 days drying in between each coat) but I can't get the first coat of tung oil (mixed 50/50 with natural turps) to dry on some silky oak stools, after four days! The timber is mostly quarter cut which with its sheeny surface might be adding to the problem. Any suggestions from experience would be welcome.

    ps. I did have a similar problem but not so extreme using tung on blackwood, but that seemed to be due more to the oil penetrating deeply into the very open grained boards I used, and then repeatedly seeping to the surface over several days.
    Last edited by JB; 23rd February 2013 at 07:55 PM. Reason: typo
    Rusty

  2. #2
    Join Date
    Apr 2005
    Location
    Nambour Qld
    Age
    88
    Posts
    0

    Default

    No response, Jamie?
    Well, for what my limited experience is worth, I have always favoured tung oil as a finish, or as a first coat to "pop" the grain, or mixed with talc as a grain filler. I think it's drying is too slow unaided, and I've always added driers (Terebine) to speed it up.
    Never experienced any problem drying on Silky Oak (or any other timber).
    Brian

  3. #3
    Join Date
    Jan 2002
    Location
    Sunshine Coast, Qld
    Posts
    117

    Default

    Thanks Brian. Could you tell me where you get terebine, and what ratio you add it to the tung oil?

    The tung on the silky oak stools still hadn't dried after five days, so I wiped them with turps (to remove excess) then applied Danish Oil. I figured that would either seal the tung, or the driers in the Danish would help to dry the tung. Anyway, it worked a treat (dried hard) and I'll now proceed with second coat of Danish.

    Thanks again for the tip.
    Rusty

  4. #4
    Join Date
    Apr 2005
    Location
    Nambour Qld
    Age
    88
    Posts
    0

    Default

    Hi Jamie

    Any specialist paint store would have terebine. A litre should last a long time.
    Feast Watson give a ratio of 1:16 but I've never found it necessary to use that much. In tung oil I use more like 1:50.

    Posting this has made me recall the first time I used tung oil and terebine. It would have been 1955 and, with all the confidence of youth, I was restoring a large silky oak table for my parents. My mother had bought it second hand about the time I was born and the top was showing the battle scars of a family of 6 children; thousands of meals consumed, eons of homework, years of card and board games. The old varnish on the turned legs and skirt had crazed.
    I stripped and sanded it and popped the grain with a grain filler of tung oil, terebine, whiting and red ochre, all things you would buy at any paint department then.
    Brian

  5. #5
    Join Date
    Nov 2007
    Location
    Albury Well Just Outside
    Posts
    2,966

    Default

    Quote Originally Posted by JB View Post
    .....The tung on the silky oak stools still hadn't dried after five days, so I wiped them with turps (to remove excess) then applied Danish Oil. I figured that would either seal the tung, or the driers in the Danish would help to dry the tung. Anyway, it worked a treat (dried hard) and I'll now proceed with second coat of Danish.....

    After thinking about what you have come up with it seems so simple.

  6. #6
    Join Date
    Jan 2002
    Location
    Sunshine Coast, Qld
    Posts
    117

    Default

    Thank you for the details of terebine mix Brian.

    And I have to ask...what's 'popping the grain'?
    Rusty

  7. #7
    Join Date
    Apr 2005
    Location
    Nambour Qld
    Age
    88
    Posts
    0

    Default

    Quote Originally Posted by JB View Post
    And I have to ask...what's 'popping the grain'?
    Just an expression for enhancing the look of the grain pattern, which an initial coat of oil does. Even more so on open grained woods if a tinted oil-based grain filler is used.
    Try it on a scrap, shellac finish with and without an initial coat of oil and you will know what we mean.
    Word of warning, though. Oil can turn very dark woods quite muddy-looking so test first on these.
    Brian

Similar Threads

  1. Tung Oil
    By Carry Pine in forum FINISHING
    Replies: 2
    Last Post: 14th May 2010, 10:42 PM
  2. When Tung Oil isn't tung oil
    By jmk89 in forum FINISHING
    Replies: 5
    Last Post: 20th November 2008, 05:49 PM
  3. Tung Oil
    By mat in forum FINISHING
    Replies: 9
    Last Post: 25th May 2008, 03:33 PM
  4. Tung Oil
    By Cornards in forum FINISHING
    Replies: 15
    Last Post: 26th December 2007, 10:26 PM
  5. Where to buy Tung Oil in BNE?
    By FlyingDuck in forum FINISHING
    Replies: 10
    Last Post: 10th July 2005, 11:46 PM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •