Results 1 to 6 of 6
  1. #1
    Join Date
    May 2010
    Location
    Brisbane
    Posts
    0

    Default removing finish from carved timber chairs

    My wife has aquired some carved timber chairs that she would like me to restore.

    They are finished in a dark red stain of some sort and I would like to strip them back to timber and finish in something more natural.

    Is some sort of media blasting the way to go? I am converned that if I try and sand the finish off I will remove some of the finer detail in the carving (and it will take forever..)

    I will try and get a picture of one of them so that one of you can hopefully identify the timber type and finish.

  2. #2
    Join Date
    May 2008
    Location
    BELL POST HILL, 3215
    Age
    87
    Posts
    0

    Default Removal.

    Hi V V,
    Although I haven't looked for it, there is a Lady selling Stripper that is a Greenie type of stuff, here on the Forums.
    Regards,
    issatree.
    Have Lathe, Wood Travel.

  3. #3
    Join Date
    Oct 2003
    Location
    Sydney,Australia
    Posts
    42

    Default

    A photo of the intended patient would help. Sanding is NOT the way to go for most carved woodwork, so you are right there.

    A lot depends on what the original finish is, what sort of timber is underneath and what has been done to the timber before you got it. I have seen a lot of really horrible results from stripping Chinese furiture which was covered in that dark purple/red lacquer - the wood is usually really coarse grained (old packing case?), full of filled holes & patches, the finish has been put on with lots of filler which often had the fine detail molded into the filler, then lacquered over the top as was the fashion around Hong Kong from the 1950's.

    Of course there is also a lot of really high quality antique furniture that was sent to HK when Mao was having his purges which was then sprayed with purple (rosewood) lacquer for the new millionaires, and some of this is being 'rediscovered' when the lacquer starts to look tatty.

    General advice - buy everyone new tooth brushes, get some small bottles of paint stripper and thinner, then soak a rag in thinner, apply generously to a hidden place (under a rail or inside) and see if the finish softens, scrub with old toothbrush - that would be shellac (good). If it doesn't change then try one of the milder strippers - Methyl somethingorother - it smells a bit like oranges, brush etc. If that doesn't work then you need to ask about one of the heavy duty strippers, vinyl gloves, fume masks etc.

    The 'professionals' use heated caustic soda and wire brushes, just about kills any colour or pattern in the wood, really only suitable for a heavy restain & then poylurethane it to death restoration.

  4. #4
    Join Date
    May 2010
    Location
    Brisbane
    Posts
    0

    Default

    I took a couple of quick photos. hopefully someone can identify the timber and tell me if the chair is worth restoring.

    Apologies for the poor picture quality.


    IMG_20130118_224826.jpg

    IMG_20130118_224147.jpg

    IMG_20130118_225255.jpg

    IMG_20130118_225227.jpg

  5. #5
    Join Date
    May 2010
    Location
    Brisbane
    Posts
    0

    Default

    is anyone able to identify this timber?

    My knowledge of timber outside building materials is pretty much non existant..

  6. #6
    Join Date
    Apr 2012
    Location
    Brisbane
    Posts
    177

    Default

    Quote Originally Posted by vincentvega View Post
    I took a couple of quick photos. hopefully someone can identify the timber and tell me if the chair is worth restoring.

    Apologies for the poor picture quality.
    Hi vincentvega. Cant help with timber type, but it looks a little like some of the better quality Indonesian rainforest hardwoods..possibly mahogany Others on here are more expert in this. Anyway..worthy of restoring? Only 1 question needs to be asked? Do you like them??? If yes, then have some fun & enjoy the outcome I say!

    Are you closer to working out what the original finish is? This will aid in choosing how to best strip it. Maybe if you know anything of their history/ age that might help.

Similar Threads

  1. Finish for Carved Picture Frame.
    By MikeG in forum FINISHING
    Replies: 5
    Last Post: 19th June 2008, 12:15 PM
  2. Removing Japanned finish
    By Andy Mac in forum FINISHING
    Replies: 2
    Last Post: 15th June 2007, 08:08 PM
  3. Removing Old finish
    By Spreyton22 in forum FINISHING
    Replies: 15
    Last Post: 11th August 2006, 03:53 PM
  4. Removing a dried out finish
    By Green in forum FINISHING
    Replies: 9
    Last Post: 15th April 2005, 12:22 PM
  5. Removing Wax finish
    By Wayne Davy in forum FINISHING
    Replies: 6
    Last Post: 18th June 2003, 11:37 AM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •