Results 1 to 7 of 7
  1. #1
    Join Date
    Oct 2008
    Location
    Syndey
    Age
    39
    Posts
    0

    Default Coffee table lacquer technique

    I all. I have just made a coffee table top for the parents in law (see pic with a 50c coin on it for scale) out of what was called "pink mahogany", and sanded to 600 after cutting and routing a nice profile for safety for toddlers.

    I have been asked to make it a hard wearing table to be used lots, so I was thinking of putting an all-weather lacquer finish on it like Cabbotts Cabothane.

    I noticed that this is now also made in a spray version.

    My question is - firstly is lacquer like Cabothane a good product to use for this, and secondly as an amateur, would I be better spraying it on to avoid paintbrush lines?

    Thanks in advance,
    Simon.
    Attached Images Attached Images

  2. #2
    Join Date
    Oct 2008
    Location
    Syndey
    Age
    39
    Posts
    0

    Default

    Oh and yes there are pockets and cracks which I filled with resin.

    I tried to lacquer over resin once, and it didn't go so well...

  3. #3
    Join Date
    May 2003
    Location
    Central Coast, NSW
    Posts
    614

    Default

    If you decide to use a brush, then if you add about 20% Penetrol that should pretty much eliminate brush and lap marks.
    Apologies for unnoticed autocomplete errors.

  4. #4
    Join Date
    Oct 2008
    Location
    Syndey
    Age
    39
    Posts
    0

    Default

    Thanks. Generally is it understood that either spraying or brushing is better for some reason? I have to buy a bottle of laquer either way, so would be happy with whatever is most likely to get a smooth even finish.

  5. #5
    Join Date
    May 2003
    Location
    Central Coast, NSW
    Posts
    614

    Default

    Not really. If you're talking about DIY-level varnish like Cabothane then I wouldnt say one looks better then the other. Brush marks can spoil the look but then so can a bad spray job (orange peel, runs etc). I mostly spray because it saves time, but I do regret that I dont get the 'hand-done' look of a really careful brush job. To some degree a spray job has a 'sitting on the surface' look, whereas brushes force product into the grain thus accentuating the grain - but thats probably more relevant to small items then to a coffee table. It probably comes down to whether you have quality spray equipment and are past the learning curve necessary to use it.
    Apologies for unnoticed autocomplete errors.

  6. #6
    Join Date
    Oct 2008
    Location
    Syndey
    Age
    39
    Posts
    0

    Default

    Thanks. I have no spray equipment. Was just thinking about buying the spray cans of poly. Sounds like doing it with a brush and mixing it down a bit is the way to go. I have spent many many hours on it so far (mostly spent levelling the slab using an old belt sander), that it would be a shame to get a dodgy finish on it.

  7. #7
    Join Date
    May 2003
    Location
    Central Coast, NSW
    Posts
    614

    Default

    I havent had any experience with spray cans so cant comment. Note its Penetrol that gives you the even finish - not thinning with turps. You might consider using a sanding sealer first as it'll give you an easy sanding surface. Most important thing is keeping the bugs and dust off as DIY varnish dries slowly so is vulnerable for a lot longer then a pro lacquer.

    I used sanding sealer, Diy varnish and penetrol on a desk recently and the finish is mirror-smooth, so it is possible with a brush.
    Apologies for unnoticed autocomplete errors.

Similar Threads

  1. Repair flaking lacquer on coffee table
    By johnno29 in forum RESTORATION
    Replies: 3
    Last Post: 5th January 2010, 11:17 AM
  2. Removing old lacquer and staining coffee table
    By switched in forum FINISHING
    Replies: 5
    Last Post: 13th June 2008, 11:06 PM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •