![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 11 of 11
Thread: Paint still tacky ....
-
4th September 2012, 07:31 AM #1
New Member
- Join Date
- Sep 2012
- Location
- canada
- Posts
- 3
Paint still tacky ....
I need help! I have painted a melamine bookcase. First I primmed the white melamine bookcase with latex primer and then gave this item two coats of regular latex paint. This was approximately three months ago and the case is still tacky when anything is place on it.
Where did I go wrong? My first attempt and thinking i messed up somewhere and was told at the paint store this was the route to take.
Many thanks for any assistance that might be offered.
-
4th September 2012, 11:23 AM #2
Senior Member
- Join Date
- Nov 2006
- Location
- kansas mostly
- Posts
- 0
If you put your hand on it does it feel sticky or does stuff that sits on the painted surface tend to stick after it's sat for a bit?
If the later, I've seen latex still do that after a year or so when primed then painted over bare wood. I think it is the nature of some latex paints.
ron
-
4th September 2012, 12:49 PM #3
SENIOR MEMBER
- Join Date
- Dec 2010
- Location
- Melbourne
- Age
- 79
- Posts
- 36
Did you sand or key the surface or use any keying treatment before you primed it?
IMO unless you treat the melamine before painting, getting it to adhere may be a problem. I don't know if this has anything to do with drying.
There is a product called ESP which claims to work so you can successfully paint glass.
I am sure you can get this in your part of the world,I'm sure I saw it at Home DepotLast edited by nrb; 4th September 2012 at 12:51 PM. Reason: Additional comment
-
4th September 2012, 09:17 PM #4
I think your problem was using a latex paint, latex ( or Acrylic ) paints take a very long time to fully cure and will have that soft sticky feel for a very long time.
Melamine has a hard surface and will not allow the paint to penetrate too much at all. In this instance I would have used a good quality oil base paint.
So from here you have two options... 1 - live with it .. or 2 - strip off all of your hard work, and start again.
Sorry
Oh yeah, welcome to the board....I try and do new things twice.. the first time to see if I can do it.. the second time to see if I like it
Kev
-
5th September 2012, 10:29 AM #5
As has been said, you have been led up the garden path on the water bassed paint.
melamine is a PITA to paint......lots of us use it arround the workshop because paint and glue does not stick to it, and abrasives hardly touch it unless you get very agressive.
Water bassed acrilics at the best of times do not go off hard and are unsuitable for furniture, the stuff can be off for years, if you put somthing hard and heavy on it for a while it will stick and pull big chunks off the stuff off...and that is on timber.
If ya want to get reasonable adhesion on melamine ( it will never be great), you need to get into the agressive solvents.
From memory "white night" do a paint specificaly designed for melamine and laminate.
Personally I'd be sanding well at 180 gritt ( use a machine) and then using my prefered thinners bassed epoxy primer undercoat, then doing whatever probably in thinners bassed paint over that.
even turps bassed enamel will remain green for weeks and not harden properly for over a month.
rather than turps bassed enamel or the proper melamine paint...ya next best non thinners top coat would be polyeurtahane paving paint, like berger jet dry.
I have used it extensively and it goes off hard....just get past the idea that it says paving pint on the tin...its an opaqe poly eurathane.
you should have no problem gettng the latex off with a sharp scraper.
cheersAny thing with sharp teeth eats meat.
Most powertools have sharp teeth.
People are made of meat.
Abrasives can be just as dangerous as a blade.....and 10 times more painfull.
-
6th September 2012, 05:59 AM #6
New Member
- Join Date
- Sep 2012
- Location
- canada
- Posts
- 3
Thank you all for the many suggestions. Its still tacky after all this time and sadly sitting empty. I shall tackle this with sandpaper and then follow up with your suggestions. Again, thank you for the many tips. Greatly appreciated.
-
6th September 2012, 07:17 AM #7
Soundman mentions one primer manufacturer, International Paints also do a Melamine primer.
Dragonfly
No-one suspects the dragonfly!
-
6th September 2012, 09:04 AM #8Any thing with sharp teeth eats meat.
Most powertools have sharp teeth.
People are made of meat.
Abrasives can be just as dangerous as a blade.....and 10 times more painfull.
-
7th September 2012, 03:40 PM #9
I would go as far as suggesting either a heatgun or a solvent (or non solvent based if you like ) paint stripper THEN sand
I try and do new things twice.. the first time to see if I can do it.. the second time to see if I like it
Kev
-
8th September 2012, 10:01 AM #10
Ig ya get hold of one of these carbide blade scrapers, I recon you will find most of it will come off no trouble at all.
they are a carbide spindle moulder knife in a handle.
A serioulsy good piece of gear.
they don't leave much behind.
At one time they where not well knwon or easily available, (I baught my first one from a saw doctor) but most hardwares and paint shops have them now.
The blades are a bit expensive if you buy them at the hardware, but if you buy from a saw doctor or indistrial woodworking supplier, they get a hell of a lot cheaper
cheersAny thing with sharp teeth eats meat.
Most powertools have sharp teeth.
People are made of meat.
Abrasives can be just as dangerous as a blade.....and 10 times more painfull.
-
10th September 2012, 01:55 AM #11
New Member
- Join Date
- Sep 2012
- Location
- canada
- Posts
- 3
Thanks to all again. Most imformative and appreciated!
best regards
Similar Threads
-
How to paint a new ceiling - sealer? which paint?
By Daren in forum PAINTINGReplies: 4Last Post: 12th April 2008, 07:24 AM -
Spa N Deck is tacky
By dan76n in forum DECKINGReplies: 3Last Post: 22nd March 2008, 10:39 AM -
Can you paint over Linseed oil with acrylic paint?
By Charleville in forum PAINTINGReplies: 2Last Post: 8th March 2008, 10:26 PM