Page 1 of 3 123 LastLast
Results 1 to 15 of 35
  1. #1
    Join Date
    Aug 2007
    Location
    Melbourne
    Posts
    110

    Default A comparison of three "Tung" Oils

    I want to point out the difference that can occur within different "Oils".
    Danish Oil is supposed to be Tung Oil, pure and simple.
    All three oils used in this comparison are Tung Oil. But some are "more" Tung Oil than others.
    Look at the two images below. The first image is that of Cabot's Danish Oil friction sealed into highly figured Red Gum. The second which was contiguous with the Danish Oil, is Liberon Pure Tung Oil treated identically.
    The white line I have pointed out is a line of grain going from the Liberon segment into the Cabot's segment. The resolution of the line is greater in the Liberon Oil than in the Cabot's. So if you use Cabot's Danish Oil, chances are you are not going to see very fine gradations in grain.
    The third figure shows Wattyl Teak (Scandinavian) Oil and the Cabot's oil. On the Left is the Wattyl Oil and on the right is the Danish. There is more darker, vertical figure present in the Wattyl oil picture than there is in the Danish oil picture.
    In fact, pictures 4 and 5 show the entire segment of the board which was oiled with either Pure Teak Oil (4) or the Danish Oil (5). On the whole, the resolution of fine grain is better in the Teak Oil.

    So..."oils ain't oils, Sol"

    Regards,

    Rob

  2. #2
    Join Date
    Mar 2008
    Location
    Townsville, Nth Qld
    Posts
    102

    Default

    Thanks for this valuable info, Rob. Where does the Feast Waston China Wood oil fit into the picture?
    regards,

    Dengy

  3. #3
    Join Date
    Aug 2007
    Location
    Melbourne
    Posts
    110

    Default

    Hi Jill,

    In this experiment, it was as good as the Pure Tung Oil and the Hard Burnishing Oil and maybe a little better than the Wattyl. The burnishing gives it more lustre than I have seen previously. I'd be very happy to use it in place of the Wattyl.

    Here's a comparison of (1) China Wood, (2) Wattyl Teak and (3) Liberon Pure Tung Oil.
    One thing about the China Wood and the Liberon. Both are names for Tung Oil, just depends on where the nuts were collected. China or South America.
    Out of the can, the Liberon was very thick. Liberon suggest diluting up to 50% with White Spirit (White Oil I think) I suspect that the China Wood has already been diluted. At some stage in the very near future (today or tomorrow) I will try doing double dilutions of the Liberon down to 50%, 25% and 12.5% oil with White Spirit and see what happens. If, as I suspect, the oil will happily still present great resolution at 50%. a 500ml can will effectively cost you $17.50!!! And last twice as long as other Oils. Excellent! If it works at 25% even better!!

    Regards,

    Rob

  4. #4
    Join Date
    Aug 2007
    Location
    Melbourne
    Posts
    110

    Default

    So...here's the doubling dilutions trial of the Liberon Pure Tung Oil.
    Pic 1 100% Tung Oil
    Pic 2 50% Tung Oil and 50% White Spirits (Dry Cleaning Fluid)
    Pic 3 25% Tung Oil and 75% White Spirits.
    I guess I should have run a negative control of White Spirit only....but I didn't!

    I'd like others to let me know where they think they'd aim to use the Oil. Pure 50% or 25% dilution. I would opt for the 50% and perhaps the 25% with a longer incubation time. (Incubation was for 25 minutes)
    BTW: The raw board was sanded dry to 400, then wet after addition of the oil or oil mix with 400, 800, 1200, 1500, 2000 and 4000 grit. You could stop anywhere in between 400 and 4000 and still get an adequate result.

    Regards,

    Rob
    Attached Images Attached Images

  5. #5
    Join Date
    Mar 2008
    Location
    Townsville, Nth Qld
    Posts
    102

    Default

    Actually Rob, from the photos and my PC monitor, they all look much the same to me, although the 25% oil is a bit paler in places
    regards,

    Dengy

  6. #6
    Join Date
    Aug 2007
    Location
    Melbourne
    Posts
    110

    Default

    Point taken, Jill.

    Excellent.

    Regards,

    Rob

  7. #7
    Join Date
    Mar 2008
    Location
    Lambton, Newcastle, NSW, Australia
    Posts
    1

    Default

    Hi LGS, White Spirit is Merican for Mineral Turps not White Oil. Great comparisons, might have to have a play myself
    Instagram: mark_aylward
    www.solidwoodfurniture.com.au


    A good edge takes a little sweat!!

  8. #8
    Join Date
    Aug 2007
    Location
    Melbourne
    Posts
    110

    Default

    Hi CH,
    Mineral Spirit is 'mericain for mineral Turps.
    White Spirits is Dry Cleaning Fluid I found out yesterday! Who knew!!

    Today I'm going to try out some liquid and some heat on the various oiled segments of the RG board. If they can stand the stress as well as the Hard Burnishing Oil, then we're all in fat city. No need for Poly anymore!
    Great Oil finish with poly durability and the bonus of not having to strip back a table top when it gets a small scratch.

    Regards,

    Rob

  9. #9
    Join Date
    Mar 2008
    Location
    Townsville, Nth Qld
    Posts
    102

    Default

    Rob, who makes the Hard Burnishing Oil? Organoil? And where do you get it from?

    I thought it was meant for wood turners, with the heat of the burnishing making it go right inot the timber.

    How would it go for boxes and frames etc?

    Keep up the great work you are doing, it is very educational, and clears up a lot of misconceptions
    regards,

    Dengy

  10. #10
    Join Date
    Aug 2007
    Location
    Melbourne
    Posts
    110

    Default

    Hi Jill,

    Organoil make Hard Burnishing Oil (HBO).
    You can get it from Carbatec for about $37.00/litre or $25.00/500ml. You can also get it at Masters for about $35.00/litre.

    HBO is designed for friction sealing, that is, heat from a source is used to burnish the oil into the wood and providing resistance to heat and liquids. The source of heat can be either the heat of friction provided by a Lathe or in the case of us impurists, a Random Orbital Sander. The friction caused by the rubbing action of the sander is sufficient for achieving the burnished result. Organoil recommend using grits up to 1500/2000. I use 4000 just because I can.
    You can buy these very high (2000 and 4000) pads from Festool. They have no holes and are synthetic pads. If you have a 150mm ROS, they will fit.
    As for the finish on boxes and the like,

    Here's some examples,

    Regards,

    Rob
    Attached Images Attached Images

  11. #11
    Join Date
    Aug 2007
    Location
    Melbourne
    Posts
    110

    Default

    Well...I've run the tests on the various Oils (all straight from the can) using the following regimes.
    1. Cold water dripped onto the oiled timber and left for 10 minutes.(Pic 1)
    2. Newly boiled water poured onto the oiled timber and left for 5 minutes. (Pic 3)
    3. A boiling pot of water laid flat on the oiled timber (Radiant Heat) and left for 5 minutes (Pic 4)
    4. Two different readily available kitchen bench cleaning agents. (Pic 5)

    While I have recorded all tests and results as images and tabulations, I can sum up as follows.

    None of the oils showed any damage or scarring as a result of any of the irritants used. Some of the oils were easier to remove evidence of the cold or hot water, but generally, all came up as they were before the tests with a little rubbing with a cotton cloth. All were fine after using the Kitchen cleaners on them.
    So hard burnishing all of the Tung Oil/Tung Oil hybrids was successful.

    Choose your weapon! Just make sure that there is no Poly in the mix.

    Regards,

    Rob

  12. #12
    Join Date
    Apr 2002
    Location
    Brisbane
    Posts
    0

    Default

    I'd like to take issue with a couple of points.

    "Danish Oil" is a rather vague term and generally means a mixture of varnish (usually polly these days) and some sort of oil or oil blend.

    While some would argue that it should be tung......it realy could be anything.

    There are various "Tung Oil" products on the market very few are "pure" tung oil.
    At the very least many of the have added metalic driers, trebine or such to make them go off in less than a month.
    Other products typically labled as " tung oil finishes" or similar contain some sort of resin or varnish component, and could be a blend of all sorts of stuff.

    If we are being fussy we realy need to know at least approximately what is in the finish and we can not rely on the name on the container or some other preconception or assertion.

    As for white spirit, it is indded clean white hydrocarbon, and is very similar to turps but is cleaner whiter and does not contain the oily component.

    White spirit is the hydrocarbon base on which many solvents are built, you will find it or similar components in turps, shellite, various thinners and it is more or less the base for petrol

    As for it being dry cleaning fluid as actually used by dry cleaners now.....I have significant doubts about that.

    I prefeer white spirit for thinning clear finishes to turps, because of the lack of the oily component, it does not seem to make things go milky as much as turps and it dries a little faster.

    If you want a clean white relativly simple hydrocarbon that evaporates cleanly, and does not taint or alter your finish, white spirit is it.

    Not to be confused with meholated spirit ( which is ethyl alcahol, ethanol),

    OR

    white parifin oil, which is a thicker oilier fraction of the refining process and is more or less baby oil, and can be had in a food safe grade & is the best thing for finishing cutting boards & such.
    Parifin oil does not polimerise or go rancid.

    cheers
    Any thing with sharp teeth eats meat.
    Most powertools have sharp teeth.
    People are made of meat.
    Abrasives can be just as dangerous as a blade.....and 10 times more painfull.

  13. #13
    Join Date
    Mar 2008
    Location
    Townsville, Nth Qld
    Posts
    102

    Default

    What an amazing result! Thanks for taking the time to do this, Rob, and for posting the results.

    I think you will start seeing a swing to oil finishes before long
    regards,

    Dengy

  14. #14
    Join Date
    Aug 2007
    Location
    Melbourne
    Posts
    110

    Default

    Hi Soundman,

    The purpose of this exercise was to take three products which should be Tung Oil or a hybrid of Tung Oil and other "goodies" and to assess their suitability for hard burnishing into timber.
    China Oil is supposedly Pure Tung Oil, since the two names are interchangeable. Teak Oil is also a Tung Oil "hybrid" product and Liberon Pure Tung Oil should be just that.
    Regardless of the true makeup of these oils, they all gave similar results in so far as definition of grain, ease of use and durability as defined by heat and liquid tolerance tests and the ability to cope with standard kitchen cleaning sprays.

    The use of White Spirit was recommended for dilution by Liberon. That is why it was used. The ability to dilute the pure oil down by 50% and 75% is a bonus and that's all. On the label, it is clearly labelled White Spirit and Dry Cleaning Fluid.

    Regards,

    Rob

  15. #15
    Join Date
    Aug 2012
    Location
    Brisbane
    Posts
    4

    Default

    LGS

    So would you suggest this finish for a floor? I was concerned that in may be a bit over slippery if it were dusty or if you had wet feet. The nudie run from the bathroom may end in a nasty bruise

Similar Threads

  1. Plastic "Bung Taps" - I want to "click" a garden hose onto the end of one...?
    By Batpig in forum NOTHING AT ALL TO DO WITH RENOVATION
    Replies: 4
    Last Post: 7th May 2017, 04:05 PM
  2. Why do so many "private" eBay sellers only offer "local pickup"?...
    By Batpig in forum NOTHING AT ALL TO DO WITH RENOVATION
    Replies: 27
    Last Post: 16th July 2016, 08:57 PM
  3. eBay: How long can you "Save" the "Draft"-listing of an item you want to sell?...
    By Batpig in forum NOTHING AT ALL TO DO WITH RENOVATION
    Replies: 0
    Last Post: 22nd January 2011, 06:04 PM
  4. "I see stupid people!" or "spot the blithering idiot"
    By journeyman Mick in forum NOTHING AT ALL TO DO WITH RENOVATION
    Replies: 46
    Last Post: 29th October 2010, 07:29 AM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •