![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 14 of 14
Thread: Rifle stock restoration
-
17th December 2010, 08:00 PM #1
New Member
- Join Date
- Dec 2010
- Location
- Cape Town
- Posts
- 6
Rifle stock restoration
Yes, I know, another thread on rifle stocks! (I did read the others)
I'm restoring a Savage 250-3000 from the 1930's (I think). Metalwork is done - now the woodwork.
Can anybody recommend some articles or books that will help me with this? In particular with:
# Stripping old gunky varnish. How and what to use so I don't damage the wood. (other than sanding)
# Checkering - do's and don'ts. Currently in good condition, but I need to strip oil/varnish.
# What other 'classic' finishes are available if I don't go the Tru-Oil route? (Another poster mentioned that Tru-Oil is actually not a true oil, but rather a poly-something with linseed oil?)
Thanks
Philip
-
18th December 2010, 08:47 AM #2
Mentholated spirits or DAA and steel wool should do the job of cleaning. Start at #2 finish with 0000
Depending on how true you wish to restore it should denote the finish you use I would think.
Cheers
SteveDiscover your Passion and Patience follows.
www.fineboxes.com.au
-
18th December 2010, 09:22 AM #3
Tool bagshas the goods on cleaning up. If it was rifle stock, after all the finishes I have used over the years I would go a Sam Maloof Danish Oil. I mix my own 30% Estapol/ polyurethane, 30% Tung oil (I use one with driers already in it) and 30% Boiled Linseed. Fast fool proof and very effective. I have been using it outdoors with huge success also. Put a coat on leave it for 15min and rub off, leave it for a day and do it again, two to three coats should be heaps. I have used an old tooth brush with metho to clean my checkering previously. Good luck
-
20th December 2010, 11:05 AM #4
GOLD MEMBER
- Join Date
- Aug 2005
- Location
- Queensland
- Posts
- 613
Avoid sanding the checkered areas as you will flatten the points if it is cut checkering - pressed checkering usually has softer points - stick with the toothbrush idea and avoid sanding checkering as much as possible. If the checkering is poor it may pay to recut it but not really recommended unless you really know what you are doing and have the correct tools.
When sanding - be very careful where there are square edges eg buttplate - if care is not taken in these areas the job will end up looking very ordinary indeed.
-
20th December 2010, 05:29 PM #5
New Member
- Join Date
- Dec 2010
- Location
- Cape Town
- Posts
- 6
Thanks for the replies. I have heard of ‘Danish Oil’ before. Will see if I can get some info on that. I'm after a satin finish - not to glossy. I will do the stripping with the toothbrush on the checkering and see what it looks like afterwards. If it’s not good, I’ll ask for some more advice on cutting checkering
. Would still like to get hold of a book with some step by step pointers…?
This will be a long term project, so you might hear from me again much later…
Cheers
Philip
-
3rd January 2011, 12:16 PM #6
Intermediate Member
- Join Date
- Jun 2008
- Location
- Mildura
- Posts
- 1
I will leave the stripping to those who would better then myself; but years ago in my mad gun days I used linseed oil on gun stocks. The oil was rubbed in with the hand palm and it left a soft glow finish. But it's a lot of rubbing.
You may already know this: to get the best sanded finish; sand with very very fine sand paper (with the grain) and wipe the stock with a damp rag to raise the grain; sand again; wipe with damp rag; and do it again and again until the finish is the same after the damp wipe; now you can start with the linseed oil.
Checking: don't sand the checking anymore then you have to. You can buy hand checking tools or make one from a small triangle file. You need to bend it.
Sorry; i have been out of the guns for too long to know any books but mr google would know
The savage 25 was a great and under rated fire arm.
-
11th March 2011, 08:28 AM #7
GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Adelaide
- Posts
- 68
I did an old lithgow some years ago
I used poly mixed with thinners......put it on like one would french polish a table...
but it was hard to get it just right...too much work and thinners would bite real quick...took a while to master it..but when I did ..came up fabulous.
.
-
27th April 2011, 01:41 AM #8
New Member
- Join Date
- Dec 2010
- Location
- Cape Town
- Posts
- 6
Feedback
Attached are some before and after pics.
The chequering was in good condition, so I did not need to re-cut.
I used Rustins Strypit and Rustins Danish oil. Lots of coats. Never managed to get all the gun oil out of the wood, but wrote it off to 'character'.
Thanks for all the advice.
Philip
-
27th April 2011, 10:28 AM #9
GOLD MEMBER
- Join Date
- Aug 2005
- Location
- Queensland
- Posts
- 613
Nice job Philip.
Personally I prefer the darker shades of timber but you have done a nice job of restoration - it should age gracefully and give you lots of satisfaction when you look/use it.
-
27th April 2011, 10:56 AM #10
GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Adelaide
- Posts
- 68
-
27th April 2011, 06:21 PM #11
GOLD MEMBER
- Join Date
- Aug 2005
- Location
- Queensland
- Posts
- 613
It certainly is - I especially like the figure in the stock.
-
27th April 2011, 10:58 PM #12
China
- Join Date
- Dec 2005
- Location
- South Australia
- Posts
- 140
Nice job Philip, looks like a pretty good job on the metal work as well, adds up up to top resto
-
29th April 2011, 08:02 PM #13
-
1st May 2011, 01:58 PM #14
Lignum Vitae maybe?
As to books if you are doing this again get the first 3 books in the series Brownell's "Gunsmith Kinks" (google Brownells gunsmith supplies). They are worth their weight in gold for the aspiring gunsmith. Plus they make entertaining reading."Entia non sunt multiplicanda praeter necessitatem"
Similar Threads
-
Rifle Stock Issue
By Gate7 in forum RESTORATIONReplies: 4Last Post: 29th January 2009, 08:24 PM -
Walnut Rifle Stock Surface Preparation & Finish
By Rabbitz in forum FINISHINGReplies: 34Last Post: 28th October 2008, 08:08 PM