![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 9 of 9
Thread: chainsaw ???s
-
11th October 2010, 09:44 AM #1
New Member
- Join Date
- Oct 2010
- Location
- canberra
- Posts
- 2
chainsaw ???s
Gday every one been looking at this site for a few weeks thought Id join. I just scored a Stihl 076 from my dad as he is in his late 70s and its to heavy to operate lol . Been overhauling it , but come to a halt , can anybody tell me how to dismantle the clutch housing so I can replace 2 springs , its the triangular nut that has me stumped L/H or R/H thread also how to hold engine to loosen it
?? Many Thanks
-
11th October 2010, 11:36 AM #2
Hi and welcome to the forum. I can't' help you I'm afraid but hopefully someone will. You may get more advice and response if you post your question in one of the other sections of the forum, perhaps "small machinery" as not all the forumites visit this part of the forum. Go to the main page and check down the list of subjects covered in the forum and ask in one of the sections that will cover chain saws. Good luck with it.
Reality is no background music.
Cheers John
-
11th October 2010, 04:02 PM #3
WELCOME
to get clutch off,
get piston to bottom of stroke, take plug out and thread string into teh cylinder until its full this will stop the piston from moving far.
you will need to make a spanner to get at that triangular nut, you will need to turn it clockwise and probably give it a good whacking, i had to use the impact gun on mine.
www.carlweiss.com.au
Mobile Sawmilling & Logging Service
8" & 10" Lucas Mills, bobcat, 4wd tractor, 12 ton dozer, stihl saws.
-
12th October 2010, 09:39 AM #4
Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 0
G'day Rob and welcome to the fount of knowledge!!!
Was going to say "Ask Carl!"But he was too quick!
-
12th October 2010, 10:09 AM #5
Member
- Join Date
- Feb 2010
- Location
- New england NSW
- Posts
- 0
chain saw
sthil make a plug with the same thread as the spark plug it would have been in the original tool kit. It is made of plastic and is the right length to kold the piston while you undo and do up the nut.
Rowley.
-
12th October 2010, 11:12 AM #6
.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 1,174
The stihl clutch tool looks like this.
Attachment 149933
This is an example of the clutch removal tool made by member Martrix. It has a large nut welded on the other side - I made a similar one myself.
As Carl said, a length of rope down the sparkplug hole will stop the crankshaft turning. Be careful that no loose fibres from the rope get left behind.
However, I would advise against using an impact gun to take it off, there have been sufficient instances of people forgetting the thread is left handed resulting in snapped crankshafts. I suggest a large spanner. I use a 12" spanner on mine and it works OK.
After all this the nut has to be torqued correctly back onto the shaft. To do this you will need access to a Torque wrench that allows you to set the torque on a left hand thread to 75 Nm (not all torque wrenches do this) - you could of course risk the crankshaft break and use an impact wrench.
-
13th October 2010, 09:41 PM #7
Welcome to the forum.
-
14th October 2010, 11:00 AM #8
New Member
- Join Date
- Oct 2010
- Location
- canberra
- Posts
- 2
Thanks Guys for all the advice !!!!!!!!!
All the handy advice worked wonders very much appreciated !!!! Great site
-
22nd October 2010, 04:37 PM #9
GOLD MEMBER
- Join Date
- Sep 2008
- Location
- texas, queensland
- Posts
- 0
mate i made a tool to remove the clutch from my 076 just a bit of heavy wall pipe with 3 slots cut into it and a plate with a big nut on the other end so i could put a socket on it .
if you need a manual or parts list shoot me a pm'If the enemy is in range, so are you.'