![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 5 of 5
Thread: Slab Table Finish
-
9th August 2009, 09:23 PM #1
Slab Table Finish
Still trying to finish my 1st attempt at a slab item.
Slab looks pretty good and have finished the polyirathene coats after a small problem.
I have read other threads on EEE with great interest.
Have tested my 1st go at EEE and Traditional Wax and really liked the look (did the reverse side of the table).
I have a few questions seeking comments:
The table is a computer table that will eventually have a seperate 3 drawer file cabinet to go with it. Do most people apply the wax to legs and rail supports as well as top?
The test section looked great but after doing it any rub with finger tip shows a mark. So does it harden or is it maybe not the finish for a computer table. Please consider that this will be a well used table.
Comments welcome.
Cheers
Ven
-
9th August 2009, 10:16 PM #2
Hi Ven, for anything with high usage, draging computers etc around, hot cups, etc I usually put 3 coats of estapol on and then polish the top with 1200 wet & dry with light oil and then again with 0000 steel wool and oil which gives it a realy smooth and attractive finish but still very tuff and serviceable.
-
9th August 2009, 10:27 PM #3
So far claw I've finished 2 brush coats and 2 spray coats (can) and a light sand with 1500 and 000 steel wool.
Now the decision what to finalise with.
Cheers
-
10th August 2009, 12:07 AM #4
If anything at all after that I usually just give it a wipe over with Feast Watson furniture polish or O'Cedar or similar.
-
28th August 2009, 10:45 PM #5
Only 3/4 happy
Posted Pics of finished desk which is stage 1. Overall happy but feel finish could be better.
I finished top with EEE Shine and followed up with UBeaut Traditional Wax. The test section I did on underside by hand went really good (I have not used Wax previously). For the top finish, I went and got a couple of Swansdown mops.
This process seemed to leave the finish a bit streaky and patchy. Admittedly you can only pick if you get down very low to surface and look along it to the bright window/door light. I feel that the mops were not the way to go but this may be beacause I've never used them before (maybe 2 higher a speed?). Had little white dust patches apper where mop stopped and this was hard to get off. This is where some of that patchyness is.
It's either accept the finish for now as up close you can almost use as a mirror when looking down or take the wax off with something and redo by hand.
Cheers
Similar Threads
-
Rock Salt Concrete Slab Finish
By Reno RSS Feed in forum CONCRETINGReplies: 0Last Post: 6th August 2009, 02:30 PM -
Wood Slab finish
By Stainso in forum FINISHINGReplies: 2Last Post: 15th July 2006, 07:35 PM -
Plywood formwork finish for coloured concrete slab
By PeterR10 in forum CONCRETINGReplies: 0Last Post: 26th June 2006, 07:52 PM -
Whats the best Jarrah Slab Finish?
By roopaw in forum FINISHINGReplies: 10Last Post: 28th October 2004, 12:10 AM