![Thanks](https://www.renovateforums.com.au/dbtech/thanks/images/thanks.png)
![Likes](https://www.renovateforums.com.au/dbtech/thanks/images/likes.png)
![Needs Pictures](https://www.woodworkforums.com/images/smilies/happy/photo4.gif)
![Picture(s) thanks](https://www.ubeaut.biz/wave.gif)
Results 1 to 11 of 11
-
25th July 2024, 03:43 PM #1
Please help with second opinion foCentral Heating Repair Diagnosis - before replacing
Please help with second opinion for Central Heating Repair Diagnosis - before replacing
Last year or two about this time a repairman sand blasted the burners and all worked until recently.
Getting a strong insistence from the accountant
that before buying a new unit
I sould I make sure.
So
Pilot Flame was going out.
When pilot lit manually
The heater would flame on and work properly.
Until over night the pilot light would be off again.
Repairman came out cleaned everything.
pilot light was on and stronger than before.
Repairman left with both working.
Controller working on and off.
everything worked the next day.
Buth this morning
Pilot light stayed lit overnight
but wouldn't flame on.
Hit the reset button.
And flame on.
Any help other than just replacing would be much appreciated.
Thanks in Advance.Thanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
-
25th July 2024, 06:51 PM #2
Make?
Model?
Controller?
System / error messages?
Age of unit?
-
27th July 2024, 12:28 PM #3
Thanks for the reply.
It's been running properly over the last two nights.
But not working this morn.
I've received the goahead if we can't figure it out.
It's worth 4k to make sure.
Make? : Airite
Model? Model: 4955
iScreen Shoter - 20240727112627843.jpg
Controller? Brivis
IMG_5974.jpg
System / error messages? None
Age of unit? 30+ - Certain original parts not available.
“So the flame is going to be the gas valve buddy and you cannot get the gas valve any more unfortunately“
As a last attempt We'll be replacing the Thermocouple Saturday avo.
Unless otherwise suggested.
Thanks in Advance.Thanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
-
27th July 2024, 01:49 PM #4
Googling the brand and model reveals nothing, have seen similar issues with other manufacturers and the manual will often give you a good breakdown of the start and run processes.
With a pilot flame as opposed to surface ignition it probably is going to come down to gas valve or flame sensor.
If there are limited parts all you can do is replace the ones that are available and if its deeper than that then replacement is probably the best option.
-
27th July 2024, 02:51 PM #5
Champion! Many thanks.
Thanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
-
28th July 2024, 07:54 AM #6
Wonder if replacing that Gas heater with an electric heater is viable.
Thanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
-
28th July 2024, 08:10 AM #7
Removed incorrect comparison query.
Thanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
-
28th July 2024, 11:46 AM #8
The motor in the gas heater will not be 600kW, dont care what the ID plate says it is wrong.
The power rating from the ID plate is 240v 5.0A, = 1200w so maybe 600W motor ?
In a gas heater the motor is for moving air and does not add to the heating power, you need to compare the heat output of the gas heater that will be kW, Mj or maybe BTU but you would need to get the specs for an Airite EX110 from the manufacturer.
The 14kW electric heater is the heating output from the unit, it is the basis of the size of the unit needed. In simple terms the larger the area to be heated the more kW's required.
You will find plenty of online calculators if you search
https://www.ozaironline.com.au/pages...ing-calculator
https://www.frozoneair.com.au/splitguidepage
Of course with ducted heating it is also about the duct design and efficiency, zoning and maximum / minimum registers open will all come into the calculations.
If you are looking to replace gas ducted heater with electric ducted then factor in complete duct replacement. IE complete new install.
Reason is that electric ducted is a lower heat and higher volume of air that is used, the ducts and vents used for the gas will most likely need to be increased in size.
-
28th July 2024, 07:04 PM #9
Thanks heaps droog. Sincerely appreciated.
Got the nix on our 1920s Edwardian.
The asthetics would not be appealing.
5 heads max on electric up grade.
We have 13 outlets.
Back to Bonaire MB530kw external as a replacement.Thanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
-
29th July 2024, 06:51 PM #10
Just had a quick flash of an idea stepping out the door.
This unit is being replaced with the MB631.
Should I salvage the fan out of the old one.
As it blasts air thru 13 ducts.
I could use the fan as a dust extractor for the shop or maybe a dust extraction table top.
Any thoughts anyone?Thanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
-
29th July 2024, 07:27 PM #11
Check the type and construction of the fan.
For ventilation yep go for it, dust extractors have a solid construction impeller as bits of timber will destroy a lesser construction designed to move only air.
Similar Threads
-
Fence repair - your opinion on 2 methods
By Joynz in forum FENCES & SCREENSReplies: 7Last Post: 17th May 2024, 11:51 PM -
HELP Ducted Heating Unit Repair - Melbourne
By MLU in forum HELP! "I've fallen and can't get up."Replies: 0Last Post: 18th May 2020, 12:16 PM -
diagnosis
By underfoot in forum JOKESReplies: 0Last Post: 25th March 2008, 05:32 PM