PDA

View Full Version : One For Router Experts















Carry Pine
10th February 2008, 08:22 PM
For background knowledge of the problem please read:

http://www.woodworkforums.ubeaut.com.au/showthread.php?t=62927

The story continues....

Used the router to cut dovetails in a blanket box using the leigh jig. At no time did the router make the grinding sound. I thought, finally my problem has ended.
Put the router back in the table today to cut a rebate and after turning it on...... the grinding, growling sound returned at start up.
But with a blinding flash, it hit me! I realised what it was.
Even the gurus couldn't help me with this one and I can't believe someone else has not had the same problem with the big Triton router.

Come on who knows what causes the grinding sound?
I can't think of a prize just now but I will give something for the first correct entry.

Carry Pine

FXST01
10th February 2008, 09:49 PM
Bearing? sounds like it only does the grinding sound when upside down in the table.

woodbe
10th February 2008, 09:54 PM
Dunno really. Mine can be a pain to lift - feels like the handle hasn't got enough leverage to lift the body of the router, so I apply pressure with my other hand to carry the weight and it operates fine. But no growling...

Is something dragging somewhere? I can't imagine that something is touching the shaft or something like that. Does it only occur in the table?

woodbe.

watson
10th February 2008, 10:08 PM
I'll be a dumb bugger and say that the bit is too big for the hole in the table???
:doh: :doh:
Just a stab

Carry Pine
11th February 2008, 08:26 AM
No, no, and no.

Have to admit even the orange caped one could not help me here.

CP

NCArcher
11th February 2008, 08:40 AM
I'll have a guess and say the thrust washer at the end of the shaft has collapsed and the brushes are hitting on the end of the commutator but only when it is mounted upside down.

Brown Dog
11th February 2008, 12:51 PM
I can't believe someone else has not had the same problem with the big Triton router

I think i have had the problem your describing there CP :-(i missed your other thread)

My big triton (which is mounted in a table) has made some wierd screaching/grinding sounds a couple of times, also when this happen the motor seems to speed up ....I had no idea what it was :?. I just switched the router off then on and all seemed to be well...so I thought nothing more of the matter. But im very interested to see what expaination you have come up with for this mysterious fault.

So come on CP stop dangling the carrot and cough up the answer :D

cheers
BD:2tsup:

Carry Pine
11th February 2008, 08:15 PM
Brown dog,

Will PM you so you don't compound the problem. I will tell all on Wednesday am (EST) if not answered.

Carry Pine

Carry Pine
13th February 2008, 08:51 AM
The answer lies in the locking bar that locks the collet while you only need one spanner to loosen the collet. It was automatically inserting when in the table and the router is lifted to change the collet. But it was not automatically retracting when the router was lowered. On start up the turning motion forced the locking bar out.
This was confirmed when I noticed 'bite marks' around the holes that the locking bar goes into.

Working on the Leigh jig I was manually inserting and extracting the bar because i wasn't using the full depth of cut.

I hope this helps someone out there. And thank you again for all the help that has been offered.

Graham

Wongo
13th February 2008, 09:18 AM
I knew it....

I had the same problem on the weekend.

I took the router out to have a good look at it and realised the locking pin wasn’t popping out when I lowered the router. I took the pin out, filed/sanded the black plastic cap, add a few drops of machines oil, put it back in and the problem was fixed.

Have I read this thread earlier I would have won something. Damn.:doh:

Honorary Bloke
13th February 2008, 09:28 AM
Have I read this thread earlier I would have won something. Damn.:doh:

First prize was a GMC router. :wink:

Carry Pine
13th February 2008, 09:36 AM
I knew it....



Have I read this thread earlier I would have won something. Damn.:doh:


First prize was 10 minutes free shopping in Greg's back yard!

CP

Wongo
13th February 2008, 09:37 AM
Thanks Bob. :D

I wonder if it is a common problem thought. It takes a little bit of dust to jam the pin. Anyone??

Wongo
13th February 2008, 09:38 AM
First prize was 10 minutes free shopping in Greg's back yard!

CP


It is better than nothing.:2tsup:

Stuart
13th February 2008, 11:15 AM
Well that sure is a curious one, and not a problem I've come across before. Add it to the collective knowledge about these tools!

I periodically clean out the router, and take that mechanism apart as part of the clean, so perhaps that was preventing the issue occurring in the first place.

I guess too, it comes down to what type of grinding noise! Next time we'll have to ask for a video, or at least a recording!

Carry Pine
13th February 2008, 07:46 PM
Thanks Stuart. I don't expect an orange cape for this one but how about a hanky? an armband?

It had the local hardware, sparkies and machinery boys here confused and when solved, they asked if I had told Triton for the sake of others. I said that you might pass it on. You've got one of those direct lines haven't you?

Graham