PDA

View Full Version : builders barrow















mrghm
16th November 2006, 06:50 PM
Hi,

Question for all, how much of a m3 does a builders barrow hold.

Bleedin Thumb
16th November 2006, 06:55 PM
Depends on how much you load into them. D:
however you can do the math. There are 8 barrows to a tonne and a tonne of sand is about 1.3 cu.m .
I'm off for a beer, my brain hurts.

SawDustSniffer
17th November 2006, 01:13 AM
um i thought there were 14 barrow loads of cement to a m^3
not quite full barrows ,:eek: reminds me of work
why dont you balence the barrow on some scales and fill it up with water
1tonne per 1m^3

back to drinking bear

Iain
17th November 2006, 08:18 AM
back to drinking bear

Barry_White
17th November 2006, 10:28 AM
You can vary the cubic metres depending what you are putting in the barrow .

You can stack fire wood a foot above the top of the barrow dirt about 8 inches above the top.

But you can't stack wet concrete above the top.

You really need to be specific as to what you want to put in it.

The other question is whatever it is, can you lift it as well as balance it while you wheel the barrow.

Iain
17th November 2006, 10:30 AM
But you can't stack wet concrete above the top.

Yes you can!!!!!!
Back to school boy and re read your physics;)

Barry_White
17th November 2006, 10:57 AM
Yes you can!!!!!!
Back to school boy and re read your physics;)

Yes but by the time you have wheeled the barrow 20 feet it will have found its own level or will be slopping over the sides or you will have tipped the barrow over where you don't want it.

I've wheeled enough concrete to know.

Never learnt the theory of physics only the practice of wheeling the concrete.

Iain
17th November 2006, 11:09 AM
I was of course referring to the meniscus, which would never take into account the perfectly flat smooth builders site, superbly smooth wheelbarrow suspension etc:D :D

Black Ned
17th November 2006, 11:23 AM
Clyde Barrow would take the contents of a bank

Bleedin Thumb
17th November 2006, 11:25 AM
Iain, Correct me if I'm wrong, (I am sure someone will) but doesn't the meniscus go up the sides of the vesicle therefore you would not be filling above the rim?

Barry_White
17th November 2006, 02:50 PM
Iain, Correct me if I'm wrong, (I am sure someone will) but doesn't the meniscus go up the sides of the vesicle therefore you would not be filling above the rim?

Can mean either depends on whether the side of the contaner is wet or dry.

http://www.answers.com/topic/meniscus

Iain
17th November 2006, 02:54 PM
I thought it was to do with surface tension, below the top it was concave, above convex.
But it's a long time since I was at high school and uni didn't address this with my subjects.

Barry_White
17th November 2006, 02:58 PM
I thought it was to do with surface tension, below the top it was concave, above convex.
But it's a long time since I was at high school and uni didn't address this with my subjects.
That's OK I didn't even know what the word meant until I Googled it.

Bleedin Thumb
17th November 2006, 03:01 PM
Either way I recon concrete would have a miniscule miniscus.
Try saying that 10 times really fast.:cool:

Barry_White
17th November 2006, 03:02 PM
I was of course referring to the meniscus, which would never take into account the perfectly flat smooth builders site, superbly smooth wheelbarrow suspension etc:D :D

Even on that basis as soon as you lift the barrow your done for.

Shouldn't all this drivel be in the Friday thread.

Barry_White
17th November 2006, 03:05 PM
Talk about hi-jacking poor mrghm's first thread.

Welcome by the way mrghm.

Iain
17th November 2006, 03:06 PM
Just bored s###less at the moment looking at a heap of sites trying to find some comparisons so I can try to screw a vendor down before he screws me.
This helps keep me alert and awake.

Bleedin Thumb
17th November 2006, 03:12 PM
Even on that basis as soon as you lift the barrow your done for.

.

Guess you have to factor in the slump as well. A really stiff mix and a short run you may be able to get away with it.
Be good for stretching the tendons.;)

journeyman Mick
17th November 2006, 08:04 PM
A good barrow will take a full load from a brickie's mixer - not one of those little 2.2 cubic feet jobs but the larger ones. Don't ask me what the capacity of the mixer is though, but Al is sure to know. (I have a concrete phobia :p ) Anyway it's a half bag mix of mortar. Any more than that and you'll be spilling it.

Mick

Harry72
17th November 2006, 09:25 PM
Its about 8 barrows per m3(providing your back is strong enough...), a cube is 35ft3, most barrows are 6cft(.16m3) but you cant fill it to the brim otherwise it would be 6 barrows.

SawDustSniffer
17th November 2006, 09:52 PM
Either way I recon concrete would have a miniscule miniscus.
Try saying that 10 times really fast.:cool:

that must be the dry ring around the barrow lip after 14 1/2 mile hikes acorss that proverbial lazer leveled site

before he asks how do i balance a wheelbarrow full of water on a set of scales , use 3 scales , or use one under 3 points and add them together

johnc
17th November 2006, 11:38 PM
With a stiff mix you should be able to get two mixes of a 2.2 mixer into the one barrow. Buggered if I know how much a 2.2 really delivers guess it depends on the mix and slope of bowl.