PDA

View Full Version : Painting doors with mini rollers















r3nov8or
19th October 2024, 12:32 PM
I'm about to paint new doors with brush for the panel-edge detail and mini roller on the flat. Already purchased Aquanamel semi gloss.

The foam and microfibre roller packaging both state they are suitable for Aquanamel (interesting that they mention only this product by name) and generically mention gloss, varnish...

I'm pretty sure the final result will depend on technique, eg paint load and how much it's worked, but looking for your experiences and any tips on mini roller choice, and technique too

Slowrenos
19th October 2024, 04:03 PM
I got a really smooth finish on a cupboard door by laying-off with brush tip after using the roller - but, gee, with water-based paint you have to be fast!

ErrolFlynn
19th October 2024, 05:45 PM
I warmed the pot of paint. (The can in hot water for a while.) And with the door resting horizontally because the paint has thinned out (being heated) it spreads easier. To minimise brush strokes. It worked, but because the only place I had space to lay it out was in the shed, which was dusty, the paint picked up a lot of dust spot marks. Perhaps in the right environment, it would be good.

droog
19th October 2024, 05:46 PM
I painted a full house set of doors using Uni-Pro microfibre mini rollers on all faces, they also got into the detail around each panel.
However I was using gloss enamel so not sure how it would compare. Perhaps some Floetrol may assist but have no personal experience.

r3nov8or
22nd October 2024, 10:18 PM
Thanks folks. A couple of the doors are already hung (bottom edge painted first). I'll give the microfibre a go!

david.elliott
29th October 2024, 05:30 PM
Had to repaint a door that the wife put a leadlight panel into after I removed the top panel and created a rebate. Only had to do one side, and the foam roller gave as good a finish as the sprayed surface on the other side. + 1 foam roller

r3nov8or
29th October 2024, 08:21 PM
Ok. I reckon I'll give both microfibre and foam a go. :) Time poor so haven't gotten stuck into it yet

mic-d
30th October 2024, 09:08 AM
I've always rolled on with an appropriate size roller and laid off very quickly with a brush. Loosened the enamel with a tiny bit of water ( I say loosened rather than thinned, it's just enough to extend working time a little and make it easier to flow). I have used floetrol in the past but not recently and the water works fine for me.

If you have any glass in the doors (not stained glass or textured) eg French doors, then get a tin of masking paint, it will save hours.

Slowrenos
31st October 2024, 08:04 AM
Masking paint? You mean you paint it on and it peels off like tape?

mic-d
31st October 2024, 09:41 AM
Masking paint? You mean you paint it on and it peels off like tape?

Exactly!

537766

It will prime unpainted timber. For doors that are already painted a light sand of the paint to knock off the gloss is enough according to the tech line but I chose to also paint on Resene Smooth Surface Primer because I wanted zero issues with the new enamel staying on the glazing bars (in fact the whole doors). That Resene primer is also excellent.

Here is a video of me removing the Seal and Peel from last years reno's. The whole house is full of 8 light French doors and side lights and 4 light awning windows so efficiency is important!

https://youtu.be/yX1Y5HPd9wg?si=EfqnhEEvBXUmucnO

Slowrenos
31st October 2024, 07:28 PM
Well, I never! When I think of all the hours I've spent fiddling with masking tape on window sashes and glazed doors...! This stuff will make a huge difference. Many thanks for heads-up and video, Mic.

mic-d
31st October 2024, 07:35 PM
Well, I never! When I think of all the hours I've spent fiddling with masking tape on window sashes and glazed doors...! This stuff will make a huge difference. Many thanks for heads-up and video, Mic.

I know right! Too much wasted time. I was skeptical at first but cutting in the Seal and Peel is super easy, you don't have to worry about brushing it on the wood, but you do want to avoid big globs of it on the wood, that's pretty easy. And another great thing is no worries about bleed under tape.

r3nov8or
31st October 2024, 07:41 PM
That stuff is a game changer!

ErrolFlynn
31st October 2024, 07:55 PM
Another notion is to paint the frame, don't worry about getting paint on the glass, then when the paint is dry but not left until it's rock hard, using a sharp knife to cut through the excess (like you did in the video), and scraping the paint from the glass using a scraper, putty knife, joint knife or similar tool.

I've never done this personally, but seen it done and was impressed.

r3nov8or
1st November 2024, 10:56 PM
Another notion is to paint the frame, don't worry about getting paint on the glass, then when the paint is dry but not left until it's rock hard, using a sharp knife to cut through the excess (like you did in the video), and scraping the paint from the glass using a scraper, putty knife, joint knife or similar tool.

I've never done this personally, but seen it done and was impressed.

No way it's coming off as clean as in the video above. If even close, would have to be perfect timing