Quiz for August 3rd

[Alias Ralph]

The last questions seemed a little hard for most of you (Bruce excepted)

So an easier question for today.

If you are making some wall frames how do you make the smoothest possible wall ?

[Grunt]

With smooth wood?

[E. maculata]

Onya Alias
String line diagonally from corner to corner??
Fer crikeys' sake do not please do not tell me it involves handplanes :eek:

[DavidG]

Don't use wood. Especially pine.

[Ashore]

Use 1/2" stainless steel plate glued to the frames
Not only smooth but stays that way





Useless infomation for the day


About a third of all Americans flush the toilet while they're still sitting on it.

[ozwinner]

Only ever, ever, use Smoothiie Woodiie


Aliie :)

[Cliff Rogers]

Call Bluey from Milla Milla, he's a F'n ace at fixing crook walls & ceilings. :D

[journeyman Mick]

By "smooth" do you mean the finished surface of the wall? That's usually what "smooth" refers to, the finished texture or lack thereof. Maybe you mean "true", as in plumb and straight, without any bows. If I wanted smmoth, I'd clad in plasterboard and make sure all the screws and joints were well set and sanded. Of course you could end up with a wall that's out of plumb, racked, bowed and twisted, but smoothe as a babies bum :p

Mick the smart@r$3

[RETIRED]

Oh Charlie. :cool:

[aussieglen]

I would assemble the frame flat on the the floor before standing - that way the wall is as flat and straight ("smooth"?) as you can get with the timber that is supplied.
Avergooday
Aussieglen

[bitingmidge]

Red velvet wallpaper with a paisly gold leaf.

Now that's Smooooooooth.

P :cool:

[Kev Y.]

Red velvet wallpaper with a paisly gold leaf.

Now that's Smooooooooth.

P :cool:

NO.. Thats COOOL,


foil wall paper is SMOOOTH :cool:

[Alias Ralph]

The ANSWER.
By smooth I meant a wall that looks even and not undulating. Many otherwise good DIY jobs are spoiled by walls that wave in and out.

STUDS
Studs are only relatively straight (within certain tolerances) which means many if not most studs have an edgewise bow.

Sort them out and use the worst studs for noggins and trimmers etc.

When you nail studs to the wall plates keep all the bows up.
By keeping all the bows the same direction there is a lot less wall straightening needed than if some studs bow one way and other studs bow the other direction.

WALL PLATES
Use the straightest timber for the top plates. These are a little harder to straighten than bottom plates. Bows in bottom plates are more easily straightened by levering it to a stringline when nailing it to the frame.

After the framing is finished but before plastering or lining use a straightedge horizontally across the wall to identify high spots and trim them with an electric plane. ( If you are a dark sider then by all means do it by hand but this will take far far longer than with electric plane) The studs only need to be straight within 1 to 1 1/2 mm.

I might have forgotten something else helpful to the DIY brigade but I'm sure the other chippies online will soon point these omissions out.

[Cliff Rogers]

I pulled all the sheeting of the sheyety job, then Bluey from Mila Milla came along & put string line marks all around the room about 10mm out from the crook warped battons & the nailed new 50mm (?) square battons to the old ones using a level as he went. Then he put up new sheeting over the whole job & it looked like a millions dollars when he was finished. The whole room ended up 10mm smaller from every wall & ceiling but it was a MUCH better job. ;)

[julianx]

put a saw cut into the hollow of the bowed studs and drive a wedge into then fit a cleat to the side of the stud to where the cut is for strength.

[kiwigeo]

All the framework in my garage walls was finished with a cabinet scraper and then sanded back to 2000 grit W and D. I then had the lot French Polished.

[Ivan in Oz]

Red velvet wallpaper with a paisly gold leaf.

Now that's Smooooooooth.

P :cool:

Just like in that place with all the 'NICE' ladies :eek: :eek: :cool:

[sman1]

Just like in that place with all the 'NICE' ladies :eek: :eek: :cool:

Really, never been there so don't know :)